Godox KNOWLED MG4K

Last Updated 2 weeks ago

Overview

The Godox KNOWLED MG4K is a high-output bi-colour point-source LED with a separate controller and G-mount modifiers. It is the white-light model in the MG4K/MG4KR pair.

MG4K is a high-output tunable-white G-mount source, not the full-colour MG4KR. Its smaller head can matter for handling, but the chosen optical package and roughly 2.3kW input still need deliberate planning.

Key specifications

SpecificationDetails
Model / capabilityMG4K, tunable white with tint; not full colour
White / tint range2,800–10,000K; −100% to +100% G/M
Published AC input2,300W at 100V/60Hz; 2,260W at 240V/50Hz
Manufacturer colour referencesCRI approximately 97; TLCI approximately 98
Intensity / curves0–100%; Linear, S-curve, Exponential and Logarithmic
Head / controller weight10kg / 6.4kg, with stated head exclusions
Head dimensionsApproximately 10.43 × 13.35 × 11.81in, excluding U-bracket/reflector
MountGodox G-mount
ControlsDMX/RDM, CRMX, Ethernet, Bluetooth and controller
Protection / temperatureIP65 head/controller; −20°C to 45°C
Key specifications

Strengths and limitations

Strengths

  • Wide white/tint tuning in a relatively compact head for this power category.
  • Internal wireless/network options allow adjustments without reaching the raised head.

Limitations

  • No full RGB colour despite the wide white/tint range.
  • Multi-kilowatt input and the separate yoke, optic and controller add substantial power and handling requirements.

Practical uses

Use it for a strong white-light source through windows, diffusion or bounce. Confirm the reflector and power mode behind an output figure, and prepare distribution for the marked input requirements.

SetupHow to use this fixture
Daylight or warm window sourceChoose the G-mount optic for the required beam and set CCT before exposure. A broad window and a distant pool may need different accessories.
Large bounceFill the useful bounce surface. A concentrated centre reading is not a measure of uniform illumination on the whole frame.
Moving location packageCompare the complete head, yoke, optic, controller and cables with the intended alternative. The quoted 10kg is not the finished rig weight.
Lighting setups

Back to contents

Output and colour

MG4K provides 2,800–10,000K white tuning and ±100% tint adjustment. Output and coverage depend on the G-mount optic, CCT, distance and cooling mode. Saturated RGB colour requires the MG4KR or another full-colour fixture.

Sources: MG4K-Product-KNOWLED.

HMI comparisons depend on the optics, working distance and illuminated area of both systems. A centre-lux result from a narrow reflector describes that beam configuration.

The MG4K adjusts white light and tint. Saturated-colour cues require filtration or a full-colour source such as the MG4KR.

Tests and reviews

Newsshooter’s walkthrough features Godox’s presentation. CineD’s IBC interview covers the bi-colour MG4K and full-colour MG4KR.

View the walkthrough and its source context.

Back to contents

Power and batteries

Godox lists 2,300W at 100V/60Hz and 2,260W at 240V/50Hz. Use the actual controller’s marked input and approved distribution for the location. The product’s “4K” branding is not a wall-power specification.

The 6.4kg controller is a separate component. Include its clamp/support, mains cable and head cable when comparing the working package or placing the head out of reach.

Control, cooling and camera operation

Control pathHardware and operating notes
Local / appController and supported Bluetooth control.
ConsoleWired/wireless DMX/RDM and CRMX as documented for the supplied unit.
NetworkEthernet configuration matched with the manufacturer’s current manual/profile.
DimmingLinear, S-curve, Exponential or Logarithmic behaviour; save the selected curve with cues.
Control options

Set white/tint, output and cooling conditions before measuring. For a transition across the wide CCT range, rehearse the real cue rather than comparing only one static daylight level.

Console profiles and firmware must match MG4K. The MG4KR uses a different colour engine and control personality.

Back to contents

Modifiers, rigging and the working package

The published 10kg head and 6.4kg controller figures exclude the head's U-bracket and reflector. G-mount optics form a separate inventory from Bowens. Check the chosen MG-series reflector, Fresnel/projection attachment and any support hardware against the exact fixture. Include yoke, optic and cables in the supported head load and keep the controller separately supported. The specified rating is IP65.

PartWorking requirement
Head10kg excluding U-bracket/reflector
Controller6.4kg separately
Front opticsChosen G-mount accessory plus required support
BalanceYoke, optic and cable load included before raising
Weather arrangementPrescribed IP65 connected configuration
MG4K separate components

The smaller head is only one handling advantage. A large Fresnel or projection optic changes the centre of gravity and occupied space. Test the actual attachment and tilt range before deciding that a stand or mounting position is suitable.

Back to contents

Alternatives and related fixtures

FixtureWhen to compare it
Godox KNOWLED MG4KRChoose MG4KR when full colour is needed, allowing for a much heavier head and different input.
Godox KNOWLED MG6KCompare the larger bi-colour system only after specifying its optics, support and greater supply requirement.
Alternative fixtures

Back to contents

What people are saying

Newsshooter, manufacturer walkthrough coverage

Newsshooter’s manufacturer walkthrough discusses efficiency and the size of the MG4K kit. Read article.

CineD, IBC interview

CineD interviews Godox about the separate MG4K and MG4KR models and their different colour capabilities. Read article.

Videos

Manufacturer walkthrough: Davi Valente explains the MG4K for Godox.

Back to contents

Rental and used-fixture checks

  • Identify MG4K bi-colour rather than MG4KR full colour.
  • Inspect G-mount lock, actual optic, yoke brake and controller/head cable.
  • Confirm marked input, firmware, fan setting and remote-control profile.

Documentation and specifications

Back to contents