Aladdin MOSAIC 4×4

Last Updated 8 hours ago

Overview

Select a photo to enlarge.

The original 4×4 produces a single overall colour and intensity setting. It is a different model from the MOSAIC 4×4 PIXEL, whose independently addressed regions are intended for moving colour and interactive effects.

Key specifications

Specification	Details
LED system	RGBWW; 600 W white / 420 W RGB ratings
CCT range	2200–12,000 K
Manufacturer colour ratings	CRI 95 / TLCI 95
Panel dimensions / mass	1100 × 1100 mm; 4 kg
Folded panel	400 × 500 mm, manufacturer reference
Frame dimensions / mass	1150 × 1160 × 170 mm; 4.5 kg
Complete cased kit mass	20.5 kg
Published beam angle	140°
Power	48 V DC; matching 100–240 V AC supply
Control	Rear controls and Bluetooth; DMX / LumenRadio through the appropriate accessory
Dimming	1–100% listed on product page

Strengths and limitations

Strengths

• Lightweight emitting head
• Broad tunable-white and RGB source
• Folds for transport

Limitations

• The frame, stand, PSU and controller still form a substantial working package.
• The bare mat cannot produce the hard, focused beam of a spotlight.
• Folding points, cables and LED tiles need protection in the case.

Practical uses

Overhead soft key. A square source can cover a table or small playing area. Build the complete frame, diffusion and spill-control arrangement before assessing stand positions and the overhead load.

Window-side ambience. Use the panel near the apparent window direction and feather it away from the near wall. It supplies broad fill rather than a concentrated shaft of sunlight.

Coloured wash. Place it close enough to make use of the large emitting area. Meter the actual saturated colour; the white-light power rating is not the RGB output.

Back to contents

Output and colour

Aladdin publishes a model-specific photometric graphic linked below. Keep its stated distances and colour settings when comparing output; adding a diffuser or grid changes the working level.

The 600 W white and 420 W RGB figures describe different operating conditions. They are not readings in lux, and adding the two figures does not describe a measured white-light output. Broad coverage is the reason to choose this format; a narrow reflector spotlight can produce a much higher centre reading with a very different field.

Setting	0.6 m	1 m	2 m	3 m
2750 K	25,400	13,200	4,330	2,210
6290 K	31,000	15,800	5,190	2,660

View Aladdin’s model-specific photometric chart.

Independent colour test

Graham Sheldon tested the original 4×4 for CineD in July 2023 with a Sekonic C-700U at three feet, without modifiers.

Controller setting	Measured CCT
5600 K	6574 K
3200 K	2993 K

Sheldon reported CRI 95.6 and used a 5030 K setting to approach a measured 5600 K. Meter the working source rather than treating that correction as a calibration for every panel.

Back to contents

Power and batteries

The manual specifies 48 V DC at 12.5 A for this panel, supplied by the matching 600 W MOSAIC power unit. The supply accepts 100–240 V AC. Ordinary 14.4/14.8 V V-mount batteries cannot be connected directly to that 48 V input.

For battery operation, use an approved converter or complete power system with the correct voltage, connector and continuous rating. Keep the power unit supported separately and leave its ventilation clear. A compatible-looking plug does not establish an electrically compatible supply.

Power package and cable identification

Component	Requirement / distinction
Panel input	48 V DC / 12.5 A in the MOSAIC series manual; 600 W white-light panel rating.
AC supply	Matching MOSAIC power supply with 100–240 V AC input. Head power is not a measured maximum wall-socket draw.
Power extension	M-EXCA3M extends the supply path; identify it separately from the M-WDEXCA3M dimmer extension.
Controller	M-WDIM adds a physical display, colour controls and DMX/LumenRadio. Check whether it is included in the quoted kit.

A battery package has to deliver the required 48 V supply through an approved conversion system. A battery’s Wh label describes capacity, while its continuous output and the converter rating determine whether full output is possible. Include the converter, cables and mounting hardware when comparing an AC kit with a battery-ready package.

Control, cooling and camera operation

The rear control box and Bluetooth app provide local and phone operation. The MOSAIC manual assigns LumenRadio control to the optional M-WDIM; wired DMX uses the appropriate dimmer or DMX-AT attachment. Full and Small Kits may include the dimmer even though a bare panel does not.

Patch the profile for the actual controller, check the start address and test fades, blackout and signal loss before raising the light. The original large-format MOSAIC is not a pixel-addressable panel. Test the chosen camera frame rate and shutter at the dimming levels used in the scene.

Choosing the control route

Route	What the working package provides
Rear buttons / Bluetooth	Quick on-panel selection and app control without the M-WDIM connected. Holding the panel’s M button for more than a second selects blackout.
M-WDIM local controls	White, RGB, HSI, filter and effects pages; the display makes repeatable settings easier than the rear buttons.
Wired DMX / LumenRadio	The M-WDIM has 5-pin input/output and a cable/radio selection in its DMX page. Older hardware and modes can have different footprints.
Bluetooth with M-WDIM attached	The February 2024 manual says the panel cannot be accessed over Bluetooth while this controller is connected. Choose the control path before rigging.

DMX personalities and patching

Aladdin’s December 2025 DMX map lists the following colour personalities for the non-pixel MOSAIC mats. Select the matching personality on the actual controller and in the console; the fixture name alone does not identify its channel footprint.

Personality	Footprint	Channel functions
Simple CCT / crossfade / RGBW	8 channels	1 intensity; 2 CCT; 3 green/magenta; 4 white/colour crossfade; 5 red; 6 green; 7 blue; 8 white.
Expert CCT / crossfade / RGBW + effects	11 channels	Channels 1–8 as above; 9 effect selection; 10 effect intensity; 11 effect speed.

For these footprints, a start address of 505 is the last complete eight-channel patch in one 512-channel universe; the eleven-channel profile must start at 502 or below. Channel 3 values 120–145 are the map’s neutral green/magenta band. Keep the crossfade and effects channels in the intended state when testing a white cue.

The older M-WDIM manual summarises two-channel white and three-channel RGB operation, while the later general map lists eight- and eleven-channel colour personalities. Check the available mode on the supplied controller instead of assuming a firmware upgrade or a different controller has the same patch.

Back to contents

Modifiers, rigging and the working package

The 4×4 Full Kit adds the matching frame, diffuser, grid and hard case to the panel, supply and control package. The Small Kit omits the complete frame-and-diffusion setup; compare the actual packing lists rather than assuming every kit contains the same rigging.

Support the fabric at its designed attachment points without forcing a sharp crease through an LED tile. Keep cable strain off the head connector, retain the power equipment separately and use suitable secondary retention for overhead work. A large diffuser and grid also catch air; head-only weight is not the rigging load.

Frame, diffusion and operating limits

The frame, diffuser and grid are size-specific. Keep the matching bungees and stand adapter with the frame, and check that the softbox skirt closes around the emitting face. A diffusion frame placed farther from the mat changes the apparent source and spill differently from the fitted softbox; compare the illuminated diffusion area at the subject.

The series manual specifies −10 to 40°C operation, a maximum 90° bend/fold, no tape directly on the LEDs, and cooling before the mat is packed. Use the intended frame to leave airflow around the head. The cable is an electrical connection, not a suspension point.

Back to contents

Alternatives and related fixtures

Fixture	Choose it for
Aladdin BI-FABRIC 2	A much smaller variable-white mat for tight locations.
amaran F22c	A smaller square RGBWW mat with a different controller and accessory system.
LiteMat Spectrum 4	Another broad colour source; compare complete rigging, control and power packages.
MOSAIC 2×4	550 × 1100 mm RGBWW mat rated 350 W white / 250 W RGB; a smaller large-format source than the 600 W MOSAIC heads, with its own frame and 48 V supply.
MOSAIC 3×6	890 × 1780 mm, 600 W white / 420 W RGB mat. Its long rectangle changes coverage and reflections without changing to a pixel-addressed system.
MOSAIC 4×4 PIXEL	The 1100 × 1100 mm format with 196 controllable pixels and M-PIXEL-DIM. Choose it for moving colour regions and interactive effects; include the extra network and mapping work.

Back to contents

What people are saying

Graham Sheldon, CineD: original MOSAIC 4×4

Sheldon found the frame quick to assemble and the package easy to transport. His reservations concern the bungee attachments, stand-mount flexibility and dialled CCT accuracy. Read the July 2023 hands-on review.

Back to contents

Videos

Aladdin MOSAIC setup, tutorial and connectivity

Manufacturer guide to the original MOSAIC system.

Back to contents

Rental and used-fixture checks

Inspect the entire mat for dark tiles, mismatched colour, damaged fold areas and loose connectors. Run warm white, cool white and each RGB channel separately.

Check the complete frame, bungees, diffuser, grid, PSU, mounting hardware and both power and control extensions. Test the M-WDIM and radio with the intended console. Pack the mat along the designed folds and protect the emitting face.

Documentation and specifications

• Official model specifications
• MOSAIC series operating manual
• MOSAIC wired dimmer manual

Browse Aladdin lights, LED mats or the equipment directory.

Back to contents