Astera AX2-100 PixelBar

Overview

Images: Astera. Select an image to enlarge; swipe the gallery on smaller screens.

The AX2-100 provides twice the pixel count and listed luminous flux of AX2-50 in one longer housing. The one-metre version reduces the number of separate heads in a long run, but its 7.4kg mass and handling length matter for transport and overhead support.

Key specifications

Specification	Details
Order Code	AX2-100
LED Engine	Titan LED Engine
Colors	RGBMintAmber
LED Power Draw	80 W
Beam Angle	21°
Field Angle	42°
Pixels	16
Battery Runtime	up to 20 hours
Battery Runtime (max. Brightness)	2 h 50 m
Charging Time (nominal)	5 hours
AC Input	96-264 VAC, 50/60 Hertz, 2 A, 104 W
AC Connector	PowerCON TRUE1 IN/OUT
Wired DMX	Yes (via 5-pin XLR)
CRMX Receiver	Built-in
BluetoothBridge BTB	No
IP Rating	IP65
Ambient Operating Temperature	0 – 40 °C / 32 – 104 °F
Weight	7.4 kg / 16.3 lbs

Back to contents

Strengths and limitations

Strengths

• Individual pixels and consistent pitch allow chases across a linked line of bars.
• BarConnect+ joins supported bars and assists addressing and alignment.
• An internal battery, AC input and wired/wireless control support temporary or extended rigs.

Limitations

• Fixed native optics require filters for a broader spread; it is not a diffuse tube.
• The published maximum-brightness runtime is 2h 50m; the 20-hour setting limits output.
• The documented standard AX2 has no built-in Bluetooth Bridge and needs a supported external bridge for AsteraApp.

Back to contents

Practical uses

Setup	Working approach
Wall wash	Tilt the feet and choose the wall distance before raising intensity. Look for scallops and gaps where adjoining bars overlap.
Stage edge or footlight	Select a wider filter if needed and shield direct lens glare. Check sightlines from the audience and every camera position.
Linked pixel line	Connect and support the bars as instructed, confirm pixel order and patch the chosen profile. Mechanical joining does not eliminate the need for power/data cables or rated suspension hardware.

Back to contents

Output and colour

The 100cm model uses 80W LED draw and produces 4,530 lumens at 5,500K. Its native-beam 1m reference at that colour temperature is 22,025 lux. These are lens-based wash-bar figures, not directly comparable with a diffuse tube’s broad distribution.

The Titan RGBMintAmber engine is specified at CRI/TLCI ≥96 over 3,200–6,500K. Optional 30°, 60° and 120° filters change coverage and intensity. Check the actual filtered beam, particularly close to a wall where the lens pattern or pixel boundaries may become visible.

Manufacturer reference	Published output
3,200K, native optics, 1m	22,125 lux
5,500K, native optics, 1m	22,025 lux
5,500K, luminous flux	4,530 lm

Back to contents

Power and batteries

Astera lists 2h 50m at maximum brightness, managed runtime up to 20 hours and a nominal five-hour charge. The 104W AC specification is separate from the 80W LED draw. Select runtime before setting the final look.

AC input is 96–264V through TRUE1 input/output. Build a linked run using the appropriate power and 5-pin DMX jumpers. Respect the circuit, cable and connector limits of the complete run; BarConnect+ is not a substitute for an electrical-distribution plan.

Back to contents

Control and camera operation

The standard model supports onboard controls, wired 5-pin DMX, CRMX, Astera UHF and infrared. Its published specification lists no built-in Bluetooth Bridge, so app use needs a compatible AsteraBox or another supported bridge.

BarConnect+ enables supported auto-addressing between connected bars. Confirm the selected personality, pixel order and start address across the entire row; automatic addressing is useful only when the patch and physical order agree. Check the slowest fades and camera shutter settings at prep.

Back to contents

Modifiers, mounting and the working package

The housing without the end hook is 1,000 × 165 × 65mm, with a published weight of 7.4kg. Adjustable feet can mount on the bottom or rear AirlineTrack, while TrackHanger and FlyBar serve specified suspended arrangements.

Use rated hardware and the manufacturer’s joining and suspension instructions for a flown row. Check every end latch, foot clamp and secondary restraint. The optional barndoors act as beam and glare control; they do not turn the fixture into a profile projector. Maintain the prescribed IP65 connections for exterior use.

Back to contents

Alternatives and related fixtures

Fixture	When to compare it
Astera AX2-50 PixelBar	The other length for a different bay size, transport requirement or number of separate heads.
Astera Titan Tube	A diffuse visible line and different emitting shape.
Aputure INFINIBAR PB12	A different pixel-bar construction and control ecosystem.

Back to contents

Reports and demonstrations

Astera: PixelBar product walkthrough

Astera’s walkthrough demonstrates the end connection, shared aiming, filters and addressing workflow. It is useful for evaluating how a row is assembled; it is manufacturer material rather than an independent battery or colour test. Read the full account.

Back to contents

Videos

Astera: AX2 PixelBar walkthrough

Astera: AX2 PixelBar introduction

Back to contents

Rental and used-fixture checks

Specify AX2-50 or AX2-100 explicitly and include the right feet, end fittings, filters, jumpers and rigging adapters. Inspect lenses, BarConnect+ latches, AirlineTrack and every foot lock.

Test the actual linked row, not only one bar. Confirm addressing, pixel direction, colour consistency, power recovery and the required battery duration. A damaged end latch or missing jumper can prevent the layout even when each lamp works by itself.

Back to contents

Documentation and specifications

Official product overview · Technical specifications · User manual · Data sheet · DMX profiles · All downloads

Back to contents

Browse Astera lights · all equipment.