ETC fos/4 Panel 24

Last Updated 5 hours ago

fos/4 Panel 24 Overview

ETC fos/4 Panel 24, 24 by 24 inch light-emitting aperture
Close-up of the ETC fos/4 Panel display and encoders
Control panelShared fos/4 Panel control interface. Photo: ETC.
ETC fos/4 Panel 24 rear housing and connections
Rear connections24 × 24 inch size. Check the installed array and connector labels on the actual head. Photo: ETC via GoKnight.
ETC fos/4 Panel family in all three aperture sizes
Compare the three sizes8 × 24, 16 × 24 and 24 × 24 inch apertures. Photo: ETC.

The ETC fos/4 Panel 24 is a 24 × 24 inch LED soft panel for studio keys, overhead ambience and broad bounced light.

It is offered as a Lustr X8 full-colour model or a Daylight HDR tunable-white model. These are different LED arrays, rather than two modes selectable on the same head.

Detail photo

  • LED Soft Panel Lustr X8 full colour or Daylight HDR tunable white.
  • Power 1,475 W typical at 120 V; 1,430 W at 230 V AC.
  • Colour Temperature 1,900–10,450 K
  • Weight 35.8 kg / 79 lb published weight
  • Beam Angle 108° with standard diffusion
  • IP Rating IP20 · indoor dry use. Read the IP rating.

Jump to Output Calculator ↓

fos/4 Panel 24 Specifications

SpecificationDetails
Light engineLustr X8 full colour or Daylight HDR tunable white
White-light range1,900–10,450K
Optical system24 × 24 inch aperture
Beam coverage108° with standard diffusion
Typical input at 120V1475W; see power section for test conditions
Published weight35.8kg; see working-package notes
DC operationNo direct DC input listed for the large panel
ProtectionIP20; indoor dry-location equipment
Control5-pin DMX/RDM; Multiverse on equipped models; NFC configuration
Model codesfos4PL24 (Lustr X8); fos4PD24 (Daylight HDR)
Flicker settings5 kHz Low; 20 kHz High on originals, 25 kHz High on later hardware; 11 kHz Medium on supported firmware. ETC user manual.

Compare Lustr X8 and Daylight HDR with ETC’s standard diffuser. To compare arrays directly, select the same colour temperature and Studio mode for both. ETC’s revision I datasheet reports foot-candles at 1, 2 and 3 m; the calculator converts those readings to lux and does not extrapolate beyond them.

Output Calculator

Select the published setup and a manufacturer distance, or enter a custom throw where supported. The results describe centre-beam output, not the brightness across the whole beam.

Camera Settings

If the calculator does not load, use the published photometric table or source on this page. JavaScript is required.

F-stop is a planning estimate, not a meter reading. It uses direct, on-axis illuminance and includes only the optics and diffusion named in the selected setup. Meter on set to account for lens transmission, filters, added diffusion, bounce, dimming and ambient light.

How the exposure estimate works

N = √(E × ISO × t / C), where E is illuminance in lux and t = shutter angle ÷ (360 × fps). The default C = 340 is a dome reference; C = 250 is a flat reference. These are calibration constants, not a measured T-stop. A small nonzero digit is tenths of a stop above the displayed full stop.

Distance estimates and comparisons

Published points are used as given. Between published points the calculator fits a curve through the two nearest readings. Outside those points it uses the inverse-square law only when the fixture’s dataset permits it. Distances outside a configuration’s supported range are reported separately. Comparisons use one shared distance and camera setup; equal lux does not imply equal coverage.

Published ETC readings by array and Studio mode
Engine and setup1 m2 m3 m
Lustr X8 · 3,200 K Brightest1,394 fc363 fc162 fc
Lustr X8 · 3,200 K Hybrid1,090 fc284 fc126 fc
Lustr X8 · 3,200 K Spectral786 fc205 fc91 fc
Lustr X8 · 4,500 K Brightest1,655 fc432 fc192 fc
Lustr X8 · 4,500 K Hybrid1,403 fc366 fc163 fc
Lustr X8 · 4,500 K Spectral1,152 fc300 fc134 fc
Lustr X8 · 5,600 K Brightest1,786 fc466 fc207 fc
Lustr X8 · 5,600 K Hybrid1,535 fc400 fc178 fc
Lustr X8 · 5,600 K Spectral1,286 fc335 fc149 fc
Daylight HDR · 3,200 K Brightest664 fc169 fc75 fc
Daylight HDR · 3,200 K Hybrid574 fc146 fc65 fc
Daylight HDR · 3,200 K Spectral484 fc123 fc55 fc
Daylight HDR · 4,500 K Brightest1,355 fc346 fc154 fc
Daylight HDR · 4,500 K Hybrid1,061 fc270 fc120 fc
Daylight HDR · 4,500 K Spectral766 fc195 fc87 fc
Daylight HDR · 5,600 K Brightest1,961 fc500 fc222 fc
Daylight HDR · 5,600 K Hybrid1,507 fc384 fc171 fc
Daylight HDR · 5,600 K Spectral1,053 fc269 fc119 fc

Back to contents

Strengths and Limitations

AspectWorking implication
StrengthBroad emitting area and selectable colour/white array options.
StrengthNFC setup and a console control path for repeatable programming.
LimitationA broad panel needs grids or flags to contain spill; it cannot produce a profile cut.
LimitationSubstantial head weight and electrical demand for the panel format.

Practical Uses

  • A large studio key or overhead base where its square aperture can illuminate a broader working area.
  • Place the fixture close to a diffusion frame for a larger apparent source; use a grid or flags to stop the panel washing the background.
  • For product work, position the panel by watching its reflection in the object rather than judging only the incident light level.

The standard diffusion produces a broad 108° distribution. This is a soft panel, so it does not replace a Fresnel for a narrow beam or a profile for shutter cuts. Additional diffusion increases the emitting area only when the diffusion itself is illuminated across a useful surface.

Back to contents

Output and Colour

ETC fos/4 Panel Lustr X8 colour gamut (PDF). The CIE 1931 plot covers the eight-colour Lustr X8 array, not the Daylight HDR version.

Manufacturer referencePublished value
Typical input at 120V1475W
Typical input at 230V1430W
Published beam108° with standard diffusion

Lumen ratings describe total flux, while lux describes light arriving at a surface. ETC’s published maximum flux for this size at 5,600 K is 61,587 lumens. That is not the lux delivered at a given distance; use the Output Calculator for the standard diffuser’s illuminance. Use ETC’s linked photometry for the exact array, lens, focus and diffusion configuration. Meter the working setup after adding colour, diffusion or other modifiers.

Lustr X8 combines deep red, red, amber, lime, green, cyan, blue and indigo for full-colour mixing. Daylight HDR uses deep red, red, mint, cyan, blue and indigo for tunable white. Both arrays have a dedicated Deep Red emitter; it does not make the Daylight HDR version a Lustr X8 full-colour fixture. The identical Kelvin range does not mean that the two versions have the same gamut or output. Record array, colour settings and spectral/output preference when matching units.

Back to contents

Power and Batteries

The large panel draws 1,475W typically at 120V and weighs 35.8kg. Its published 12.4A draw leaves little capacity on a shared 15A circuit. The large model lacks the smaller panels’ direct battery input.

Check the supply lead, grounding, connector rating and total circuit load. Published fixture-per-circuit counts assume a particular breaker and supply condition; they are not a universal instruction for every outlet or distribution system. Account for startup current as well as steady running draw.

Back to contents

Control, Cooling and Camera Operation

Control pathOperation
Wired control5-pin DMX and RDM. Match operating mode and DMX footprint to the console profile.
Wireless controlCity Theatrical Multiverse on equipped versions. It is a different system from CRMX; confirm the transmitter and receiving hardware.
NFCETC Set Light configures supported fixture properties at close range. NFC setup is separate from continuous wireless DMX control.
Cooling and PWMActive fan cooling; use the specified frequency choices and test the actual fan setting, dimming level, shutter and frame rate.

Test low-level fades as well as full output. A high PWM frequency alone does not prove flicker-free results at every frame rate and shutter combination. Listen to the fan at the microphone position after the fixture has reached working temperature. Save cooling, colour and operating-mode settings with the lighting notes.

Back to contents

Modifiers, Rigging and the Working Package

A rear Griprail accepts the specified M6 standard T-nut hardware. Use the documented yoke or Griprail mounting arrangement; handles and accessory channels do not make arbitrary overhead attachments suitable.

IP20 describes an indoor fixture, so plan a suitable dry environment. Keep vents unobstructed and follow the regional manual’s mounting and clearance instructions. For overhead work, use the designated mounting and secondary attachment points with hardware rated for the complete assembly.

Back to contents

Alternatives and Related Fixtures

CompareWhen it helps
ETC Source Four tungstenA tungsten profile when shutter cuts and pattern projection matter; it needs an appropriate lamp and external dimming.
ETC lighting hubCompare ETC’s panel, Fresnel and profile formats by the beam needed for the job.
All equipmentCompare other manufacturers with the same source size, working distance and modifier.

Back to contents

What People Are Saying

Cinematography Mailing List’s 2024 tests at Loyola Marymount University measured the PL24 Lustr X8. The results below describe that sample and test configuration, not the PD24.

Field Feedback at a Glance

What worked

  • CML measured 2,140 lux at 3 m with the bare PL24 set to 3,200 K in Spectral mode, with SSI 83 and TLCI 95. CML/LMU’s PL24 test.
  • At the nominal 5,600 K setting, CML measured 2,650 lux at full, 1,350 lux at 50% and 271 lux at 10%, close to proportional intensity changes in that setup. CML/LMU’s PL24 test.
  • CML’s modifier test measured 3,660 lux at 3 m with the intensifier versus 2,480 lux with standard diffusion. That’s a centre-reading gain, not a gain across the entire beam. CML/LMU’s PL24 test.

Drawbacks to plan for

  • The bare test sample read 5,219 K against a nominal 5,600 K setting. It read 5,509 K with standard diffusion in the modifier comparison, so meter with the actual front in place. CML/LMU’s PL24 test.
  • At 35.8 kg (79 lb), the 24 × 24 in head has substantially more rigging weight than either smaller panel. Plan for the modifier and mounting hardware as well. ETC datasheet.
  • The PL24/PD24 lack both the smaller models’ direct DC input and AC power-through. ETC lists a 1,600 W maximum, so plan the non-dim supply for the large panel itself. ETC user manual.

The CML/LMU’s PL24 test also includes beam photos with bare, light, standard, heavy and intensifier fronts. Use those images to compare coverage and spill; the meter table alone only shows centre readings.

Videos

Levi Whitney of UpHill Cinema demonstrates the fos/4 Panel and Fresnel family. This is an operating reference, not a separate test of the Panel 24 and its two arrays.

Back to contents

Rental and Used-Fixture Checks

  • Confirm the model label, array and regional power rating; housing appearance alone may not identify the light engine.
  • Inspect the diffuser, accessory retainers and Griprail mounting hardware.
  • Test every colour channel, low-level fades, fan operation and the intended wired or wireless control mode.
  • Check firmware against the manufacturer’s support notes and run the required camera test before rigging.

Documentation and Specifications

ETC’s additional fos/4 family mounting view.

ETC colour-calibration modes · ETC fixture directory and photometry downloads

Photographs: ETC. Family photographs and shared housing details are identified in their captions.

Back to contents

Browse ETC lighting · all equipment.