ETC ColorSource Fresnel V MAX

Last Updated 5 hours ago

ColorSource Fresnel V MAX Overview

ETC ColorSource Fresnel V MAX fixture
ColorSource Fresnel V family control and connection detail
Control panelThe shared ColorSource Fresnel V family control and connection detail. Photo: ETC.
ETC PSF1191 eight-leaf Fresnel barndoor
Compatible barndoorETC specifies the PSF1191 7.5-inch eight-leaf barndoor for the Fresnel V and V MAX. Shown on its own. Photo: Solotech.

The ETC ColorSource Fresnel V MAX is a five-colour RGBIL LED Fresnel with motorised zoom, adjustable locally or through DMX. It is the higher-output MAX version, with separate electrical and photometric specifications from the original Fresnel V. Indigo and lime extend the colour-mixing options beyond a basic RGB fixture; this is a different engine from ETC’s eight-colour Lustr X8.

Detail photo

  • RGBIL LED Fresnel RGBIL: red, green, blue, indigo and lime
  • Power 208 W, typical at 120 V AC
  • Colour Temperature 3,200 K and 5,600 K ETC’s published photometry settings.
  • Weight 6.24 kg
  • Beam Angle 15–40° beam / 25–55° field, motorised zoom
  • IP Rating IP20 · indoor dry locations. IP ratings guide.

Jump to Output Calculator ↓

ColorSource Fresnel V MAX Specifications

SpecificationDetails
Light engineRGBIL: red, green, blue, indigo and lime
White-light rangeColour mixing; white settings depend on the control profile
Optical system190mm aperture
Beam coverage15–40° beam / 25–55° field, motorised zoom
Typical input at 120V208W; see power section for test conditions
Published weight6.24kg; see working-package notes
DC operationAC powered; no direct battery input listed
ProtectionIP20; indoor dry-location equipment
Control5-pin DMX/RDM; Multiverse on equipped models; NFC configuration
Flicker settings5kHz default / 25kHz via RDM
WirelessMultiverse on equipped versions; verify the ordered model

Back to contents

ColorSource Fresnel V MAX Output Calculator

Estimate centre-beam output or compare two settings at the same throw. The calculator uses candela from the ETC ColorSource Fresnel V MAX datasheet, rev E, pp. 5–6. These readings are for the V MAX, not the standard V or IP65 VXT MAX. ETC’s photometry chart records 235 W in Full On Direct Boost and 196 W in standard Full On Direct. These are chart conditions, not the separate typical 120 V input rating.

At 5 m (16.4 ft) in narrow (15.1°), Full On Direct Boost gives about 5,684 lx at beam centre; Full On Direct gives about 4,702 lx. The reference table works without JavaScript.

Published intensity data and calculation method

Lux = candela ÷ distance in metres squared. Foot-candles = lux ÷ 10.7639. The camera estimate uses f-number = √(lux × ISO × shutter time ÷ meter reference). The small digit is tenths of a stop, not a T-stop.

The minimum throw is 3.048 m, the closest tabulated throw used here. Beyond that, these are inverse-square estimates at beam centre, not measurements or coverage predictions. Only ETC’s published focus and output settings are included; diffusion, accessories and dimming are not modelled. Meter the working setup.

FocusFull On Direct BoostFull On Direct3,200 K Brightest3,200 K Spectral5,600 K Brightest5,600 K Spectral
Narrow (15.1°)142,106117,54094,60988,64397,63098,014
Medium (20°)95,78079,22263,76659,74565,80266,061
Wide (40°)28,70923,74619,11417,90819,72419,801

Back to contents

Strengths and Limitations

AspectWorking implication
StrengthAdjustable coverage without replacing the whole head.
StrengthNFC setup and a console control path for repeatable programming.
LimitationWash optics cannot project sharp gobos or shutter cuts.
LimitationActive cooling and IP20 protection require attention to sound and location conditions.

Practical Uses

  • Set a repeatable top or back wash for filmed performances and stage productions.
  • Use a narrower setting for an accent, then widen for a larger scene without exchanging the whole fixture.
  • Balance saturated scenic colour against white keys through the production camera; equal console percentages do not produce equal exposure.

Motorised zoom can change coverage in a cue, but also changes centre illuminance and edge position. Establish level at the chosen zoom. During recorded dialogue, listen for zoom-motor noise before including a live focus change in the shot.

Back to contents

Output and Colour

Manufacturer referencePublished value
Maximum measured field flux11,296 lumens (wide, Full On Direct Boost)
Maximum measured sphere flux11,821 lumens (wide, Full On Direct Boost)

Lumen ratings describe total flux, while lux describes light arriving at a surface. Do not read the flux table as a lux measurement at a particular distance. Use ETC’s linked photometry for the exact array, lens, focus and diffusion configuration. Meter the working setup after adding colour, diffusion or other modifiers.

The RGBIL engine uses five colours, including indigo and lime. It is a colour-mixing system rather than a dedicated variable-white fos/4 engine. Select the correct console personality and calibrated operating mode before matching units; a raw emitter mix is a different control choice from a calibrated colour request.

Back to contents

Power and Batteries

ETC lists 208 W typical input at 120 V. The separate photometry chart records 196 W in Full On Direct and 235 W in Full On Direct Boost. The operating range is 100–240V AC, 50/60Hz. Supply constant power and use the fixture’s electronic dimming; the power-through connector does not make the fixture suitable for a conventional phase-dimmed circuit.

Check the supply lead, grounding, connector rating and total circuit load. Published fixture-per-circuit counts assume a particular breaker and supply condition; they are not a universal instruction for every outlet or distribution system. Account for startup current as well as steady running draw.

Back to contents

Control, Cooling and Camera Operation

Control pathOperation
Wired control5-pin DMX and RDM. Match operating mode and DMX footprint to the console profile.
Wireless controlCity Theatrical Multiverse on equipped versions. It is a different system from CRMX; confirm the transmitter and receiving hardware.
NFCETC Set Light configures supported fixture properties at close range. NFC setup is separate from continuous wireless DMX control.
Cooling and PWMActive fan cooling; use the specified frequency choices and test the actual fan setting, dimming level, shutter and frame rate.

Test low-level fades as well as full output. A high PWM frequency alone does not prove flicker-free results at every frame rate and shutter combination. Listen to the fan at the microphone position after the fixture has reached working temperature. Save cooling, colour and operating-mode settings with the lighting notes.

Back to contents

Modifiers, Rigging and the Working Package

Use the correct frame and retention system for the 190mm aperture. Fit only approved accessories, keep the fan path clear and support the fixture through its yoke. A nominal seven-inch lens description is not a universal accessory fitting.

IP20 describes an indoor fixture, so plan a suitable dry environment. Keep vents unobstructed and follow the regional manual’s mounting and clearance instructions. For overhead work, use the designated mounting and secondary attachment points with hardware rated for the complete assembly.

Back to contents

Alternatives and Related Fixtures

CompareWhen it helps
ETC Source Four tungstenA tungsten profile when shutter cuts and pattern projection matter; it needs an appropriate lamp and external dimming.
ETC lighting hubCompare ETC’s panel, Fresnel and profile formats by the beam needed for the job.
All equipmentCompare other manufacturers with the same source size, working distance and modifier.

Back to contents

What People Are Saying

Field Feedback at a Glance

These points are specific to the indoor ColorSource Fresnel V MAX. They come from ETC’s bench data and operating documentation, not independent crew testing. Reviews of the original V or the outdoor VXT MAX do not establish how this head performs.

What worked

  • ETC’s wide-zoom photometry gives 11,296 field lumens in wide Full On Direct Boost, versus 9,344 in standard Full On Direct. That is useful headroom for the wide part of a wash, but neither value is the output of a 3200 K or 5600 K preset.
  • ETC’s V MAX datasheet shows that the motorised zoom can be set locally or from the lighting desk in suitable DMX profiles. That lets an operator trim the wash from the console after the fixture is hung.
  • The V MAX introduced Studio DMX mode, which ETC’s v4.3.0 release notes say was extended to other ColorSource V fixtures. Use the V MAX fixture profile and its documented white-light controls when setting up camera-facing cues.

Drawbacks to plan for

  • Circuit planning needs more than the 208 W typical figure at 120 V. ETC’s wide-zoom photometry shows 235 W in the wide Boost condition and 196 W with standard Full On Direct; the electrical table also gives separate inrush and power-link limits.
  • The ETC’s v4.3.0 release notes list a known issue in which a V MAX can shift between colours with the fan disabled. Before shooting dialogue with the fan off, check the installed firmware and run a recorded camera and sound test at the actual level.
  • ETC’s V MAX datasheet lists IP20. Use it in dry indoor conditions; the separate VXT MAX is the weather-rated model, not another name for this one.

Videos

ETC’s walkthrough covers both Fresnel V and Fresnel V MAX operation. It is a manufacturer demonstration, not an independent output or noise test. The figures above refer to the V MAX.

Back to contents

Rental and Used-Fixture Checks

  • Confirm the model label, array and regional power rating; housing appearance alone may not identify the light engine.
  • Inspect the Fresnel lens, focus travel, barn-door retention and yoke lock.
  • Test every colour channel, low-level fades, fan operation and the intended wired or wireless control mode.
  • Check firmware against the manufacturer’s support notes and run the required camera test before rigging.
  • Check the fixture software before cueing. ETC’s v4.3.0 release note records fixes for colour oscillation with the Fresnel V MAX fan disabled and a misleading zoom readout on startup. Test the selected fan mode and compare the displayed zoom with the actual beam after a power cycle.

Documentation and Specifications

ETC colour-calibration modes · ETC fixture directory and photometry downloads

Photographs: ETC. Family photographs and shared housing details are identified in their captions.

Back to contents

Browse ETC lighting · all equipment.