ETC fos/4 Panel 16

Last Updated 5 hours ago

fos/4 Panel 16 Overview

ETC fos/4 Panel 16, 16 by 24 inch light-emitting aperture
Close-up of the ETC fos/4 Panel display and encoders
Control panelShared fos/4 Panel control interface. Photo: ETC.
ETC fos/4 Panel 16 rear housing and connections
Rear connections16 × 24 inch size. Check the installed array and connector labels on the actual head. Photo: ETC via GoKnight.
ETC fos/4 Panel family in all three aperture sizes
Compare the three sizes8 × 24, 16 × 24 and 24 × 24 inch apertures. Photo: ETC.

The ETC fos/4 Panel 16 is a 16 × 24 inch LED soft panel for studio keys, overhead ambience and broad bounced light.

It is offered as a Lustr X8 full-colour model or a Daylight HDR tunable-white model. These are different LED arrays, rather than two modes selectable on the same head.

Detail photo

  • LED Soft Panel Lustr X8 full colour or Daylight HDR tunable white.
  • Power 955 W typical at 120 V; 935 W at 230 V AC.
  • Colour Temperature 1,900–10,450 K
  • Weight 25.4 kg / 56 lb published weight
  • Beam Angle 108° with standard diffusion
  • IP Rating IP20 · indoor dry use. Read the IP rating.

Jump to Output Calculator ↓

fos/4 Panel 16 Specifications

SpecificationDetails
Light engineLustr X8 full colour or Daylight HDR tunable white
White-light range1,900–10,450K
Optical system16 × 24 inch aperture
Beam coverage108° with standard diffusion
Typical input at 120V955W; see power section for test conditions
Published weight25.4kg; see working-package notes
DC operation24–36V DC; reduced output may apply
ProtectionIP20; indoor dry-location equipment
Control5-pin DMX/RDM; Multiverse on equipped models; NFC configuration
Model codesfos4PL16 (Lustr X8); fos4PD16 (Daylight HDR)
Flicker settings5 kHz Low; 20 kHz High on originals, 25 kHz High on later hardware; 11 kHz Medium on supported firmware. ETC user manual.

Compare Lustr X8 and Daylight HDR with ETC’s standard diffuser. To compare arrays directly, select the same colour temperature and Studio mode for both. ETC’s revision I datasheet reports foot-candles at 1, 2 and 3 m; the calculator converts those readings to lux and does not extrapolate beyond them.

Output Calculator

Select the published setup and a manufacturer distance, or enter a custom throw where supported. The results describe centre-beam output, not the brightness across the whole beam.

Camera Settings

If the calculator does not load, use the published photometric table or source on this page. JavaScript is required.

F-stop is a planning estimate, not a meter reading. It uses direct, on-axis illuminance and includes only the optics and diffusion named in the selected setup. Meter on set to account for lens transmission, filters, added diffusion, bounce, dimming and ambient light.

How the exposure estimate works

N = √(E × ISO × t / C), where E is illuminance in lux and t = shutter angle ÷ (360 × fps). The default C = 340 is a dome reference; C = 250 is a flat reference. These are calibration constants, not a measured T-stop. A small nonzero digit is tenths of a stop above the displayed full stop.

Distance estimates and comparisons

Published points are used as given. Between published points the calculator fits a curve through the two nearest readings. Outside those points it uses the inverse-square law only when the fixture’s dataset permits it. Distances outside a configuration’s supported range are reported separately. Comparisons use one shared distance and camera setup; equal lux does not imply equal coverage.

Published ETC readings by array and Studio mode
Engine and setup1 m2 m3 m
Lustr X8 · 3,200 K Brightest929 fc242 fc108 fc
Lustr X8 · 3,200 K Hybrid726 fc189 fc84 fc
Lustr X8 · 3,200 K Spectral524 fc137 fc61 fc
Lustr X8 · 4,500 K Brightest1,103 fc288 fc128 fc
Lustr X8 · 4,500 K Hybrid935 fc244 fc108 fc
Lustr X8 · 4,500 K Spectral768 fc200 fc89 fc
Lustr X8 · 5,600 K Brightest1,190 fc310 fc138 fc
Lustr X8 · 5,600 K Hybrid1,023 fc267 fc119 fc
Lustr X8 · 5,600 K Spectral857 fc224 fc99 fc
Daylight HDR · 3,200 K Brightest443 fc113 fc50 fc
Daylight HDR · 3,200 K Hybrid383 fc98 fc43 fc
Daylight HDR · 3,200 K Spectral322 fc82 fc37 fc
Daylight HDR · 4,500 K Brightest904 fc230 fc102 fc
Daylight HDR · 4,500 K Hybrid707 fc180 fc80 fc
Daylight HDR · 4,500 K Spectral511 fc130 fc58 fc
Daylight HDR · 5,600 K Brightest1,308 fc333 fc148 fc
Daylight HDR · 5,600 K Hybrid1,005 fc256 fc114 fc
Daylight HDR · 5,600 K Spectral702 fc179 fc80 fc

Back to contents

Strengths and Limitations

AspectWorking implication
StrengthBroad emitting area and selectable colour/white array options.
StrengthNFC setup and a console control path for repeatable programming.
LimitationA broad panel needs grids or flags to contain spill; it cannot produce a profile cut.
LimitationSubstantial head weight and electrical demand for the panel format.

Practical Uses

  • A broader interview or dialogue key where the source needs to cover two seated people.
  • Place the fixture close to a diffusion frame for a larger apparent source; use a grid or flags to stop the panel washing the background.
  • For product work, position the panel by watching its reflection in the object rather than judging only the incident light level.

The standard diffusion produces a broad 108° distribution. This is a soft panel, so it does not replace a Fresnel for a narrow beam or a profile for shutter cuts. Additional diffusion increases the emitting area only when the diffusion itself is illuminated across a useful surface.

Back to contents

Output and Colour

ETC fos/4 Panel Lustr X8 colour gamut (PDF). The CIE 1931 plot covers the eight-colour Lustr X8 array, not the Daylight HDR version.

Manufacturer referencePublished value
Typical input at 120V955W
Typical input at 230V935W
Published beam108° with standard diffusion

Lumen ratings describe total flux, while lux describes light arriving at a surface. ETC’s published maximum flux for this size at 5,600 K is 41,058 lumens. That is not the lux delivered at a given distance; use the Output Calculator for the standard diffuser’s illuminance. Use ETC’s linked photometry for the exact array, lens, focus and diffusion configuration. Meter the working setup after adding colour, diffusion or other modifiers.

Lustr X8 combines deep red, red, amber, lime, green, cyan, blue and indigo for full-colour mixing. Daylight HDR uses deep red, red, mint, cyan, blue and indigo for tunable white. Both arrays have a dedicated Deep Red emitter; it does not make the Daylight HDR version a Lustr X8 full-colour fixture. The identical Kelvin range does not mean that the two versions have the same gamut or output. Record array, colour settings and spectral/output preference when matching units.

Back to contents

Power and Batteries

At 955W typical on 120V and 25.4kg, this is a substantial head. Plan the stand, transport route and distribution before choosing it for a small location.

Check the supply lead, grounding, connector rating and total circuit load. Published fixture-per-circuit counts assume a particular breaker and supply condition; they are not a universal instruction for every outlet or distribution system. Account for startup current as well as steady running draw.

Direct battery operation is available on this size through the specified DC input and supported adapter arrangement. Check voltage, connector polarity, continuous current and battery-output limits. Watt-hours estimate energy capacity; they do not establish whether a battery can supply the required load.

Back to contents

Control, Cooling and Camera Operation

Control pathOperation
Wired control5-pin DMX and RDM. Match operating mode and DMX footprint to the console profile.
Wireless controlCity Theatrical Multiverse on equipped versions. It is a different system from CRMX; confirm the transmitter and receiving hardware.
NFCETC Set Light configures supported fixture properties at close range. NFC setup is separate from continuous wireless DMX control.
Cooling and PWMActive fan cooling; use the specified frequency choices and test the actual fan setting, dimming level, shutter and frame rate.

Test low-level fades as well as full output. A high PWM frequency alone does not prove flicker-free results at every frame rate and shutter combination. Listen to the fan at the microphone position after the fixture has reached working temperature. Save cooling, colour and operating-mode settings with the lighting notes.

Back to contents

Modifiers, Rigging and the Working Package

A rear Griprail accepts the specified M6 standard T-nut hardware. Use the documented yoke or Griprail mounting arrangement; handles and accessory channels do not make arbitrary overhead attachments suitable.

IP20 describes an indoor fixture, so plan a suitable dry environment. Keep vents unobstructed and follow the regional manual’s mounting and clearance instructions. For overhead work, use the designated mounting and secondary attachment points with hardware rated for the complete assembly.

Back to contents

Alternatives and Related Fixtures

CompareWhen it helps
ETC Source Four tungstenA tungsten profile when shutter cuts and pattern projection matter; it needs an appropriate lamp and external dimming.
ETC lighting hubCompare ETC’s panel, Fresnel and profile formats by the beam needed for the job.
All equipmentCompare other manufacturers with the same source size, working distance and modifier.

Back to contents

What People Are Saying

For Panel 16, the production accounts below document the Lustr X8 PL16. Panel-specific rigging and power notes apply to both PL16 and Daylight HDR PD16.

Field Feedback at a Glance

What worked

  • 80six used eight Lustr X8 PL16 panels with two fos/4 Fresnels to light a test commercial at MPTS 2022 on an 8 × 3.5 m LED volume. 80six’s production breakdown.
  • Mobeon integrated four medium Lustr X8 panels in its ground-supported green-screen studio, alongside twelve small panels and four Fresnels. ETC’s Mobeon Studios case study.
  • The 16 × 24 in aperture doubles the face height of Panel 8 without increasing face width, useful when there’s room for a taller source but not a wider one. ETC datasheet.

Drawbacks to plan for

  • ETC specifies 955 W at 120 V in Direct at full and 1,070 W maximum. Don’t use the typical figure alone for circuit planning. ETC user manual.
  • At 25.4 kg (56 lb) before added modifiers, this is not a lightweight panel. ETC identifies the rear handle pairs as this size’s carry and safety-cable points. ETC datasheet; ETC user manual.
  • The PL16/PD16 accept 24–36 V DC only when AC isn’t available, and output can be reduced on battery. Confirm the intended output on the actual power package. ETC user manual.

80six’s case documents use of the PL16 alongside other fixtures, not a side-by-side test of Lustr X8 and Daylight HDR.

Videos

80six’s behind-the-scenes video from MPTS 2022 documents the production using eight PL16 panels. For a fixture-operation walkthrough, UpHill Cinema’s fos/4 Panel and Fresnel demonstration covers the family, not every panel size or array.

Back to contents

Rental and Used-Fixture Checks

  • Confirm the model label, array and regional power rating; housing appearance alone may not identify the light engine.
  • Inspect the diffuser, accessory retainers and Griprail mounting hardware.
  • Test every colour channel, low-level fades, fan operation and the intended wired or wireless control mode.
  • Check firmware against the manufacturer’s support notes and run the required camera test before rigging.

Documentation and Specifications

ETC’s additional fos/4 family mounting view.

ETC colour-calibration modes · ETC fixture directory and photometry downloads

Photographs: ETC. Family photographs and shared housing details are identified in their captions.

Back to contents

Browse ETC lighting · all equipment.