ETC Source Four LED Series 3 Daylight HDR

Last Updated 5 hours ago

Daylight HDR Overview

ETC Source Four LED Series 3 profile with XDLT lens
Source Four LED Series 3 control panel
Control panelSource Four LED Series 3 control panel
ETC 7060A1013 A-size steel gobo holder with a round opening and handle
Gobo holderETC A-size steel gobo holder (7060A1013), a compatible accessory for projecting patterns.

The ETC Source Four LED Series 3 Daylight HDR is an LED profile spotlight for shuttered beams, gobos and controlled specials. Its Daylight HDR engine prioritises tunable white light rather than the full saturated gamut of Lustr X8. The body, shutter barrel and lens tube must be specified as a compatible working package.

The Daylight HDR and Lustr X8 share a Series 3 housing. Check the fixture label and console profile rather than assuming the same array is installed.

Detail photo

  • LED Profile Daylight HDR six-colour array: deep red, red, mint, cyan, blue and indigo.
  • Power 340 W typical at 120 V AC / 330 W at 230 V AC, Direct at Full.
  • Colour Temperature 1900–10,450 K tunable white.
  • Weight 8.9 kg published weight; add the actual lens and mounting hardware.
  • Beam Angle Lens-dependent; the fixed-lens chart includes nominal 5°–90° tubes.
  • IP Rating IP20 · indoor dry locations. IP ratings guide.

Jump to Output Calculator ↓

Daylight HDR Specifications

SpecificationDetails
Light engineDaylight HDR tunable white
White-light range1,900–10,450K
Optical system80mm gate; lens tube ordered for the required angle
Beam coverageLens-dependent; interchangeable profile optics
Typical input at 120V340W; see power section for test conditions
Published weight8.9kg; see working-package notes
DC operationAC operation; no direct battery input specified
ProtectionIP20; indoor dry-location equipment
Control5-pin DMX/RDM; Multiverse on equipped models; NFC configuration
Pattern sizeA or B, with compatible holder
Flicker settings5kHz / 25kHz

Daylight HDR Output Calculator

Compare fixed lens tubes at the same throw. Estimates show centre-beam illuminance for the Daylight HDR, not the Lustr X8. The candela and lumen values below are from ETC’s Series 3 photometry table, page 7 (alternate copy of the same datasheet).

At 5 m (16.4 ft), 19° XDLT is approximately 6,261 lx and 19° EDLT approximately 3,554 lx at beam centre. The reference below works without JavaScript.

Published fixed-lens data and calculation method

Lux = candela ÷ distance in metres squared. Foot-candles = lux ÷ 10.7639. The camera estimate uses N = √(lux × ISO × shutter time ÷ C). A small digit after the standard f-stop is tenths of a stop. It is not a measured T-stop.

Use 1–100 m as a tool input range, not a validated measurement range. Inverse-square estimates can be unreliable at short throws. This does not model beam edges, colour changes, diffusion, shutters, gobos, or a dimmed head. Check the barrel required for each lens family and meter the actual setup. Equal nominal angles do not guarantee equal beam profiles. Zoom positions are not included.

Lens tubeCentre intensity (cd)Total flux (lm)
5° XDLT686,0067,074
10° XDLT412,3049,600
14° XDLT200,0859,191
19° XDLT156,52410,708
26° XDLT89,66812,346
36° XDLT51,95412,733
50° XDLT28,34810,404
70° XDLT18,03712,271
19° EDLT88,8496,606
26° EDLT88,18011,278
36° EDLT60,32511,331
50° EDLT/LED29,1059,675
5° standard431,2704,190
10° standard264,9156,396
14° standard125,5826,586
19° standard76,2335,364
26° standard60,5877,055
36° standard50,49611,687
50° standard28,6639,914
70° standard17,67911,928
90° standard12,36612,359

Back to contents

Strengths and Limitations

AspectWorking implication
StrengthPrecise gate, shutter and pattern control with interchangeable optics.
StrengthNFC setup and a console control path for repeatable programming.
LimitationThe lens and barrel configuration affects output, size and accessory compatibility.
LimitationActive cooling and IP20 protection require attention to sound and location conditions.

Practical Uses

  • Create a clean window-shaped pool with the shutters, keeping the gate in focus for a hard edge or slightly defocusing for a softer transition.
  • Project a breakup pattern onto scenery using a correctly sized gobo and holder. Check pattern orientation and focus at the actual throw.
  • Use as a controlled backlight where conventional barn doors would spill onto the lens or a nearby wall.

Profile optics image the gate, shutters and patterns. Changing lens angle changes coverage and centre illuminance. XDLT lenses are designed for Series 3 performance, while ETC also documents other lens configurations. Confirm the exact barrel and lens combination before ordering; the beam angle is not an electronic zoom setting.

Back to contents

Output and Colour

Manufacturer referencePublished value
Headline maximum flux (ETC source specification)14,214 lumens
Direct at Full, 120V340W
Maximum input, online electrical guide375W

Lumen ratings describe total flux, while lux describes light arriving at a surface. Do not read the flux table as a lux measurement at a particular distance. ETC’s lens-specific table separately reports 14,503 lumens for the 15°–30° XDLT zoom at its mid setting; that zoom is not in the fixed-lens finder. Use ETC’s linked photometry for the exact array, lens, focus and diffusion configuration. Meter the working setup after adding colour, diffusion or other modifiers.

Lustr X8 and Daylight HDR are different hardware arrays. Select the version for the required colour work, then compare lens-specific photometry. A narrow lens raises centre illuminance by concentrating the beam; it does not increase the electrical power of the fixture.

Back to contents

Power and Batteries

The Daylight HDR datasheet lists 340W at 120V in Direct at Full, with 6.3W idle. ETC’s online electrical guide separately specifies 375W maximum consumption. Feed the unit from a non-dimmed 100–240V AC source and size distribution for the marked rating and startup requirements.

Check the supply lead, grounding, connector rating and total circuit load. Published fixture-per-circuit counts assume a particular breaker and supply condition; they are not a universal instruction for every outlet or distribution system. Account for startup current as well as steady running draw.

Back to contents

Control, Cooling and Camera Operation

Control pathOperation
Wired control5-pin DMX and RDM. Match operating mode and DMX footprint to the console profile.
Wireless controlCity Theatrical Multiverse on equipped versions. It is a different system from CRMX; confirm the transmitter and receiving hardware.
NFCETC Set Light configures supported fixture properties at close range. NFC setup is separate from continuous wireless DMX control.
Cooling and PWMActive fan cooling; use the specified frequency choices and test the actual fan setting, dimming level, shutter and frame rate.

Test low-level fades as well as full output. A high PWM frequency alone does not prove flicker-free results at every frame rate and shutter combination. Listen to the fan at the microphone position after the fixture has reached working temperature. Save cooling, colour and operating-mode settings with the lighting notes.

Back to contents

Modifiers, Rigging and the Working Package

Order the lens tube, appropriate pattern holder and mounting clamp as required. The 8.9kg datasheet weight includes the barrel; the chosen lens adds to the working assembly. A Fresnel or CYC adapter changes the optical purpose and must be treated as that configuration.

IP20 describes an indoor fixture, so plan a suitable dry environment. Keep vents unobstructed and follow the regional manual’s mounting and clearance instructions. For overhead work, use the designated mounting and secondary attachment points with hardware rated for the complete assembly.

Back to contents

Alternatives and Related Fixtures

ETC Source Four LED Series 3 Lustr X8. Compare the Lustr X8 array when saturated colour is more important; use its own data, not the Daylight HDR readings.

CompareWhen it helps
ETC Source Four tungstenA tungsten profile when shutter cuts and pattern projection matter; it needs an appropriate lamp and external dimming.
ETC lighting hubCompare ETC’s panel, Fresnel and profile formats by the beam needed for the job.
All equipmentCompare other manufacturers with the same source size, working distance and modifier.

Back to contents

What People Are Saying

ETC’s Series 3 demonstration explains the two arrays and lens system. It is a manufacturer demonstration. UpHill Cinema also documents use of Series 3 in filmmaking through ETC’s linked case study; the account does not identify the array used, so it is not evidence of Daylight HDR performance. View the source.

The practical notes below use ETC’s specifications for this model. Field accounts are not photometric tests.

What Works

  • White-focused output: The six-emitter Daylight HDR array tunes white between 1,900 and 10,450 K. For a window slash or daylight-balanced special, choose this array on its own merits rather than borrowing Lustr X8 figures.
  • Shape a hard edge precisely: Use the profile’s shutters to cut the beam off a wall or fit a pattern holder to project a breakup. The lens tube determines the spread.
  • Configure fixtures before a hang: ETC’s Set Light app can write settings via NFC; a DMX run or compatible Multiverse link handles cue control afterward.

What to Watch For

  • Different array, different job: The Daylight HDR’s six emitters are not the Lustr X8’s eight. Do not expect to match a saturated Lustr cue just by copying its settings.
  • Book the right lens and measurement: ETC publishes separate figures by lens; the fixed-lens calculator does not cover the 15–30° XDLT zoom. If that is the rented lens, read its own table.
  • Allow for the Daylight HDR electrical draw: ETC lists 340 W typical at 120 V for this version. Do not size branch loads using the lower Lustr X8 number; check the maximum and inrush in the electrical documentation.

Videos

ETC’s Source Four LED Series 3 overview covers both arrays and the shared fixture controls. The Daylight HDR figures above do not apply to Lustr X8.

Back to contents

Rental and Used-Fixture Checks

  • Confirm the model label, array and regional power rating; housing appearance alone may not identify the light engine.
  • Inspect the lens, shutters, barrel lock, pattern holder and focus travel.
  • Test every colour channel, low-level fades, fan operation and the intended wired or wireless control mode.
  • Check firmware against the manufacturer’s support notes and run the required camera test before rigging.

Documentation and Specifications

ETC colour-calibration modes · ETC fixture directory and photometry downloads

Photographs: ETC. Family photographs and shared housing details are identified in their captions.

Back to contents

Browse ETC lighting · all equipment.