Kino Flo Image 85 DMX (Fluorescent)

Last Updated 8 hours ago

Overview

Kino Flo Image 85 DMX lighting fixture
Rear of the Image 85 DMX showing its yoke and built-in ballast housing.
Rear controls housingRear of the Image 85 DMX showing its yoke and built-in ballast housing. Photo: CineGear.
Front of an Image 85 DMX fitted with an eggcrate and suspended in its yoke.
Eggcrate and yokeFront of an Image 85 DMX fitted with an eggcrate and suspended in its yoke. Photo: District Auction.

The Kino Flo Image 85 DMX is an eight-lamp, four-foot fluorescent softlight with electronics integrated into a substantial studio-style fixture. It is suited to broad keys, overhead lighting, cyclorama or screen illumination and controlled soft fill where the fixture can remain on a stand or grid as part of a larger lighting system.

The Image 85 fluorescent fixture has yoke and pole-operated configurations. It is not the later Image 87, a four-lamp Image 45 or an LED-retrofitted body. Its DMX primarily switches lamps and selects output mode; it should not be treated as a modern LED panel with continuous colour and dimmer channels.

Detail photo

  • Eight Four-Foot LampsImage 85; F75/T12 fluorescent system
  • Regional AC Versions8.6 A at 120 V or 4.3 A at 230 V
  • Integrated ElectronicsNot Flathead 80 or Image 87
  • Weight 38 lb / 17.1 kg Yoke. Pole-operated: 40 lb / 18 kg with lamps
  • Nine DMX AddressesEight lamp controls plus HO/STD Catalogue configuration: 4,748 lux at 1 m.
  • IP Rating The cited manufacturer documentation does not establish a numeric rating; keep the fixture and power equipment dry. Read the IP rating guide.

Jump to Output Calculator ↓

Key Specifications

SpecificationDetails
ModelsIMG-85X yoke; IMG-85P pole-operated, regional 120 V or 230 V versions
LampsEight F75/T12 four-foot True Match fluorescent tubes
Colour examplesKF29, KF32 and KF55; specialised blue/green lamp options are documented
Supply / input-current figures120 V: 8.6 A; 230 V: 4.3 A, 50/60 Hz, as specified
Ballast frequency25 kHz
Yoke dimensions54 × 28 × 6½ inches / 137 × 71 × 16.5 cm
Yoke weight with lamps38 lb / 17.1 kg in manufacturer literature
Pole-operated dimensions / mass54½ × 28 × 6½ inches; 40 lb / 18 kg
Mount / supportJunior-pin yoke hardware; identify the installed assembly
Local controlsRotary lamp-count selection, HO/STD and power
DMX footprintNine addresses: eight lamp controls plus HO/STD control
DMX modesIndividual-lamp or Fixture mode; five-pin XLR in/out with termination switch
STD versus HOSTD is approximately half a stop below HO in the operating manual
Power-loss versus DMX-lossManual warns that loss of DMX signal holds the last command
Kino Flo’s original catalogue and model-family operating manual. Historical fixture and ballast revisions are identified separately.

Output Calculator

Select the published setup and a manufacturer distance, or enter a custom throw where supported. The results describe centre-beam output, not the brightness across the whole beam.

Camera Settings

If the calculator does not load, use the published photometric table or source on this page. JavaScript is required.

F-stop is a planning estimate, not a meter reading. It uses direct, on-axis illuminance and includes only the optics and diffusion named in the selected setup. Meter on set to account for lens transmission, filters, added diffusion, bounce, dimming and ambient light.

How the exposure estimate works

N = √(E × ISO × t / C), where E is illuminance in lux and t = shutter angle ÷ (360 × fps). The default C = 340 is a dome reference; C = 250 is a flat reference. These are calibration constants, not a measured T-stop. A small nonzero digit is tenths of a stop above the displayed full stop.

Distance estimates and comparisons

Published points are used as given. Between published points the calculator fits a curve through the two nearest readings. Outside those points it uses the inverse-square law only when the fixture’s dataset permits it. Distances outside a configuration’s supported range are reported separately. Comparisons use one shared distance and camera setup; equal lux does not imply equal coverage.

Strengths and Limitations

Strengths

  • A bank of fluorescent tubes provides a broad close source.
  • The established modifier and mounting system supports fast setup.

Limitations

  • Lamp type, age and ballast configuration affect colour and output.
  • Inspect older connectors, lamp holders and ballast cabling before use.

Practical Uses

Eight parallel tubes create a broad emitting area suited to a large soft key or overhead fill. The yoke provides an adjustable studio-style support, while a pole-operated version is useful for inaccessible grid positions. The integrated electronics make the fixture a different handling proposition from a Flathead with two remote ballasts.

For screens or a cyclorama, the useful result is even illumination across the receiving surface, not maximum centre lux. Choose spacing, angle, output mode and lamp count to control overlap, then meter the screen. Specialised blue or green lamps are different spectral sources; their availability in the lamp list does not make the fixture an RGB colour-mixing light.

SetupWorking approach
Close interview keySet lamp arrangement and diffusion, then check white balance through the camera.
Reflection or fillOrient the bank for the required highlight and control spill with the correct louver.
Lighting setups

Back to contents

Output and Colour

The original catalogue publishes these Image 85 readings. They are useful references for a healthy fluorescent system, but replacement lamps, operating temperature, output mode and accessories need to match the test context before treating the numbers as a prediction for a particular used unit.

DistanceCentre illuminance
1 m4,748 lux
2 m1,443 lux
3 m678 lux
4 m394 lux
Manufacturer catalogue values. These are Image 85 figures, not Image 45 or Image 87 specifications.

The rotary selector controls lamp count locally. Applying DMX disables manual lamp and HO/STD controls in the documented arrangement; the manual describes address 000 for local control with the data cable connected and a five-second transition delay. Check that operating mode before diagnosing the physical controls as broken.

STD reduces output by approximately half a stop relative to HO. The ninth address selects that function, not colour temperature. The manual also states that a fixture holds its last command if DMX disappears: turning off the console is not a reliable way to extinguish the lamps. Send an explicit off/blackout command and follow the site’s proper shutdown procedure.

Back to contents

Power and Batteries

Use the correct 120 V or 230 V fixture version and its nameplate rating. The specified 8.6 A or 4.3 A values belong to the relevant regional unit; do not assume universal input or calculate the mains load simply as eight times a nominal tube wattage. The electronics require the supply arrangement specified in the manual.

Use matched lamps, keep cooling paths open and allow stable operation before a critical colour or exposure check. Switching lamp count changes the luminous surface and reflection pattern. Test unusual shutter angles or high-speed work with the actual lamp and ballast combination rather than treating high-frequency catalogue language as an unlimited guarantee.

Control, Cooling and Camera Operation

The Image 85/45 manual assigns eight addresses to lamps and the ninth to HO/STD. In Individual mode the console can switch lamp positions separately. In Fixture mode a fader steps the lamp count according to the documented sequence. Neither is a continuously variable LED dimmer applied uniformly to every tube.

The console’s output curve should follow the manual’s linear-response guidance. Check the selected mode, base address, termination and cable type, and do not use microphone cable as a substitute for proper DMX data cable. A generic ‘eight-lamp panel’ personality can omit the ninth function or produce unexpected switching.

Back to contents

Modifiers, Rigging and the Working Package

A lamped yoke fixture is listed at 38 lb, and the pole-operated version at 40 lb; packed cases and full rigging loads are different figures. Inspect the yoke, pin, clamps or suspension hardware, tilt locks and pole mechanisms as applicable. Include barn doors, louver, gel frame and power-cable pull when planning support.

Test all eight channels and both output modes, the DMX sockets and terminator, local controls and signal-loss behaviour. Inspect sockets, lamp clips, cable, strain relief and the electronics for damage or signs of overheating. Protect tubes during handling and confirm replacement-lamp and service support. An Image converted to LED needs an updated identity and the conversion’s own operating and output information.

Back to contents

Alternatives and Related Fixtures

A Flathead 80 provides a similar eight-lamp source with remote ballasts and a different mounting arrangement. The Image 45 is a narrower four-lamp fixture; the Image 87 is another revision and must be checked from its own documentation. Current LED softlights add electronic colour and continuous dimming conveniences. The Image 85 is most useful when a complete healthy fixture fits an established studio or location workflow.

FixtureChoose it for
Kino Flo FreeStyle LEDA separate LED engine and controller system.
Kino Flo Diva-Lite LEDAn LED alternative with different colour modes and power hardware.
Related fixtures

Back to contents

What People Are Saying

Field feedback at a glance

What worked

  • Directional backlight without moving fixtures. On It, Michael Galbraith’s crew rigged 17 daylight-lamped Image 85s around the sewer set’s ceiling opening. They switched on groups to suit each camera direction. American Cinematographer
  • Overhead coverage on a large set. Lighting programmer Nic Jones recalled that Image 85s provided top light across the cave set on Divergent, alongside separate hard and coloured sources. ICG Magazine
  • Even chroma-key coverage. ScreenLight & Grip’s stage report credits the Image 85’s soft, wide spread for lighting large blue and green screens evenly. ScreenLight & Grip

Drawbacks to plan for

  • Eight tubes can be too bright for low ambience. On It, the crew sometimes ran just three tubes per fixture to keep the general light level down. American Cinematographer
  • Neutral current can build up across a large rig. ScreenLight & Grip measured 13.62 A on the neutral with one Image 85 on each phase, while average phase current was 7.77 A. Have the set electrician evaluate the distribution before using these fixtures in quantity. ScreenLight & Grip
  • Cold starts draw a short surge. ScreenLight & Grip measured 70 A of cold-start inrush on its single test fixture. Flag simultaneous switch-on of a large bank during power planning. ScreenLight & Grip

Fluorescent System and Package Overview

New England Studios presents its Image 85 rental kit, giving a view of the complete studio-light package. Match the actual ballast, mounting hardware and DMX arrangement to the intended installation. View the source.

Videos

Kino Flo Image 85 DMX (Fluorescent): Family Guide

A fluorescent-system guide; the exact fixture and ballast specifications are given above.

Back to contents

Rental and Used-fixture Checks

Check the exact model, matching power components and control leads. Inspect the emitting surface, protective parts, mounts and connectors. Test the intended operating mode, low-level control and camera settings before rigging.

Documentation and Specifications

Manufacturer operating manual, original manufacturer catalogue with photometrics, Kino Flo manual archive and photograph and rental-inventory source. Current lamp and service-part availability should be confirmed for the exact unit.

Product photograph: Product image via Expressway Cinema Rentals.

Back to contents