ETC Source Four LED Series 3 Lustr X8

Last Updated 6 hours ago

Lustr X8 Overview

ETC Source Four LED Series 3 profile with XDLT lens
Source Four LED Series 3 control panel
Control panelSource Four LED Series 3 control panel
ETC 7060A1013 A-size steel gobo holder with a round opening and handle
Gobo holderETC A-size steel gobo holder (7060A1013), a compatible accessory for projecting patterns.

The ETC Source Four LED Series 3 Lustr X8 is an LED profile spotlight for shuttered beams, gobos and controlled specials. Its eight-colour Lustr X8 engine includes deep red for full-colour mixing and adjustable white light.

The body, shutter barrel and lens tube must be specified as a compatible working package.

Detail photo

  • LED Profile The Lustr X8 uses an eight-colour LED array that includes deep red. The Daylight HDR is a separate model.
  • 375 W Max + Integrated PSU 307 W typical at 120 V in Direct at Full; 100–240 V AC.
  • Colour Temperature1,900–10,450 K Adjustable white.
  • Weight 8.9 kg / 19.6 lb with barrel; the lens adds weight.
  • Beam Angle Interchangeable lens tubes. Confirm barrel compatibility and the nominal tube angle.
  • IP RatingIP20 For indoor, dry locations. Read the IP rating.

Jump to Output Calculator ↓

Lustr X8 Specifications

SpecificationDetails
Light engineLustr X8 eight-colour array
White-light range1,900–10,450K
Optical system80mm gate; lens tube ordered for the required angle
Beam coverageLens-dependent; interchangeable profile optics
Typical input at 120V307W; see power section for test conditions
Published weight8.9kg; see working-package notes
DC operationAC operation; no direct battery input specified
ProtectionIP20; indoor dry-location equipment
Control5-pin DMX/RDM; Multiverse on equipped models; NFC configuration
Pattern sizeA or B, with compatible holder
Flicker settings5kHz / 25kHz

Lustr X8 Output Calculator

Compare fixed lens tubes at the same throw. Estimates show centre-beam illuminance for the Lustr X8, not the Daylight HDR. The candela and lumen values below are from ETC’s Series 3 photometry table, page 7 (alternate copy of the same datasheet).

At 5 m (16.4 ft), 19° XDLT is approximately 5,794 lx and 19° EDLT approximately 3,030 lx at beam centre. The reference below works without JavaScript.

Published fixed-lens data and calculation method

Lux = candela ÷ distance in metres squared. Foot-candles = lux ÷ 10.7639. The camera estimate uses N = √(lux × ISO × shutter time ÷ C). A small digit after the standard f-stop is tenths of a stop. It is not a measured T-stop.

Use 1–100 m as a tool input range, not a validated measurement range. Inverse-square estimates can be unreliable at short throws. This does not model beam edges, colour changes, diffusion, shutters, gobos, or a dimmed head. Check the barrel required for each lens family and meter the actual setup. Equal nominal angles do not guarantee equal beam profiles. Zoom positions are not included.

Lens tubeCentre intensity (cd)Total flux (lm)
5° XDLT630,3446,031
10° XDLT375,0287,823
14° XDLT185,1257,544
19° XDLT144,8568,921
26° XDLT82,35710,120
36° XDLT47,21510,426
50° XDLT26,0178,499
19° EDLT75,7425,349
26° EDLT81,6129,399
36° EDLT52,1509,302
50° EDLT/LED24,7698,045
5° standard398,0723,523
10° standard236,9415,370
14° standard114,6255,359
19° standard70,3414,482
26° standard54,9985,849
36° standard46,1869,732
50° standard24,6697,893
70° standard16,1569,926
90° standard11,13710,259
70° XDLT14,1979,945

Back to contents

Strengths and Limitations

Strengths

  • Precise gate, shutter and pattern control with interchangeable optics.
  • NFC setup and a console control path for repeatable programming.

Limitations

  • The lens and barrel configuration affects output, size and accessory compatibility.
  • Active cooling and IP20 protection require attention to sound and location conditions.

Practical Uses

  • Create a clean window-shaped pool with the shutters, keeping the gate in focus for a hard edge or slightly defocusing for a softer transition.
  • Project a breakup pattern onto scenery using a correctly sized gobo and holder. Check pattern orientation and focus at the actual throw.
  • Use as a controlled backlight where conventional barn doors would spill onto the lens or a nearby wall.

Profile optics image the gate, shutters and patterns. Changing lens angle changes coverage and centre illuminance. XDLT lenses are designed for Series 3 performance, while ETC also documents other lens configurations. Confirm the exact barrel and lens combination before ordering; the beam angle is not an electronic zoom setting.

Back to contents

Output and Colour

ETC’s Lustr X8 colour-gamut reference explains why the fixture selects the closest available colour when an XY or HSI request falls outside the emitter gamut.

Manufacturer referencePublished value
Highest flux in ETC’s current lens table11,103 lumens · 15°–30° XDLT zoom at ETC’s “Mid” setting. Earlier tables list 10,889 lumens for the 25°–50° standard zoom at its narrow setting.
Direct at Full, 120V307W
Maximum input, online electrical guide375W

Lumen ratings describe total flux, while lux describes light arriving at a surface. Do not read the flux table as a lux measurement at a particular distance. Use ETC’s linked photometry for the exact array, lens, focus and diffusion configuration. Meter the working setup after adding colour, diffusion or other modifiers.

Lustr X8 and Daylight HDR are different hardware arrays. Select the version for the required colour work, then compare lens-specific photometry. A narrow lens raises centre illuminance by concentrating the beam; it does not increase the electrical power of the fixture.

Back to contents

Independent Measurement

See the CML/LMU daylight colour test and its exact setup in What people are saying. It is independent of the ETC candela figures used by the Output Calculator.

Power and Batteries

The Lustr X8 datasheet lists 307W at 120V in Direct at Full, with 6.3W idle. ETC’s online electrical guide separately specifies 375W maximum consumption. Feed the unit from a non-dimmed 100–240V AC source and size distribution for the marked rating and startup requirements.

Check the supply lead, grounding, connector rating and total circuit load. Published fixture-per-circuit counts assume a particular breaker and supply condition; they are not a universal instruction for every outlet or distribution system. Account for startup current as well as steady running draw.

Back to contents

Control, Cooling and Camera Operation

Control pathOperation
Wired control5-pin DMX and RDM. Match operating mode and DMX footprint to the console profile.
Wireless controlCity Theatrical Multiverse on equipped versions. It is a different system from CRMX; confirm the transmitter and receiving hardware.
NFCETC Set Light configures supported fixture properties at close range. NFC setup is separate from continuous wireless DMX control.
Cooling and PWMActive fan cooling; use the specified frequency choices and test the actual fan setting, dimming level, shutter and frame rate.

Test low-level fades as well as full output. A high PWM frequency alone does not prove flicker-free results at every frame rate and shutter combination. Listen to the fan at the microphone position after the fixture has reached working temperature. Save cooling, colour and operating-mode settings with the lighting notes.

Back to contents

Modifiers, Rigging and the Working Package

Order the lens tube, appropriate pattern holder and mounting clamp as required. The 8.9kg datasheet weight includes the barrel; the chosen lens adds to the working assembly. A Fresnel or CYC adapter changes the optical purpose and must be treated as that configuration.

IP20 describes an indoor fixture, so plan a suitable dry environment. Keep vents unobstructed and follow the regional manual’s mounting and clearance instructions. For overhead work, use the designated mounting and secondary attachment points with hardware rated for the complete assembly.

Back to contents

Alternatives and Related Fixtures

ETC Source Four LED Series 3 Daylight HDR. Compare the separate Daylight HDR array for its own white-light photometrics and lens data.

For another ETC colour profile, see the ETC ColorSource Spot V.

CompareWhen it helps
ETC Source Four tungstenA tungsten profile when shutter cuts and pattern projection matter; it needs an appropriate lamp and external dimming.
ETC lighting hubCompare ETC’s panel, Fresnel and profile formats by the beam needed for the job.
All equipmentCompare other manufacturers with the same source size, working distance and modifier.

Back to contents

What People Are Saying

Field Feedback at a Glance

What worked

  • Warmer white gave skin more depth. Halliday preferred the rich skin tones of the Lustr X8 to the Series 2 Lustr when mixing a tungsten-like white. (Rob Halliday, LSi (2021))
  • Crisp shutter and gobo edges with XDLT. Halliday found the newer optics could produce a sharply defined cut or pattern and still soften without distracting artefacts. (Rob Halliday, LSi (2021))
  • Narrow XDLT tubes delivered more punch. Halliday noticed the brightness improvement most with the narrower tubes, from 19° down, compared with the Series 2 Lustr. (Rob Halliday, LSi (2021))

What to watch for

  • The shutters felt loose on the tested unit. Halliday found that the shutters on his review unit felt less firm than on a traditional Source Four. Check how well the actual rental unit holds a cut. (Rob Halliday, LSi (2021))
  • Quieter cooling can limit output. Halliday noted that capping fan speed in a quiet venue can reduce light output if the head reaches its thermal limit. (Rob Halliday, LSi (2021))
  • Check daylight colour on your camera. CML/LMU’s test measured 5258 K and a TLCI of 40 at the 5600 K setting, at full power with 216 diffusion at the front and the meter at 3 m (9.85 ft). Those numbers describe that test setup only. (CML/LMU camera and lighting test (2024))

ETC’s Series 3 demonstration explains the two arrays and lens system. It is a manufacturer demonstration. UpHill Cinema also documents use of Series 3 in filmmaking through ETC’s linked case study; that is application coverage rather than an independent photometric comparison. View the source.

Videos

The following family demonstration provides an operating reference. Specifications above refer to the named model and configuration.

Back to contents

Rental and Used-Fixture Checks

  • Read the model label to confirm you have the Lustr X8, not the Daylight HDR. You can’t identify the installed LED array from the housing alone. Check the power rating on the unit.
  • Inspect the lens, shutters, barrel lock, pattern holder and focus travel.
  • Test every colour channel, low-level fades, fan operation and the intended wired or wireless control mode.
  • Check firmware against the manufacturer’s support notes and run the required camera test before rigging.

Before You Book

  • Package: Specify the Lustr X8 light engine, a compatible shutter barrel and the exact lens tube, such as a 19° XDLT. Match the lens family and angle in the output calculator.
  • Power: Use a non-dimmed AC feed and plan for the 375 W maximum, not the 307 W typical reading.
  • Control: Confirm the control mode and run your dimming and flicker checks with the camera settings you’ll use.

Documentation and Specifications

ETC colour-calibration modes · ETC fixture directory and photometry downloads

Photographs: ETC. Family photographs and shared housing details are identified in their captions.

Back to contents

Browse ETC lighting · all equipment.