Aladdin MOSAIC MINI 1×2

Last Updated 6 hours ago

Overview

Select a photo to enlarge.

The 300 × 600 mm face provides a longer source than the MINI 1×1 and doubles the listed white-light power. Both models list 20 W RGB, so the longer panel should not be assumed to double saturated-colour output.

Key specifications

Specification	Details
LED system	100 W bi-colour / 20 W RGB
CCT range	2300–12,000 K
Manufacturer colour ratings	CRI 95 / TLCI 95
Panel dimensions	300 × 600 × 5 mm
Panel mass	682 g
Dimmer	MM-DIM-LM; V-mount
Dimmer mass / dimensions	Product page: 373 g; 95 × 152 × 50 mm
Control	Local dimmer, Bluetooth, LumenRadio and wired DMX with appropriate cable
Protection rating	IP20 on product page
Kit choices	MM-2-KITCVM / MM-2-KITG

Strengths and limitations

Strengths

• Thin head with a separate battery controller
• White and RGB operation
• Frame and softbox options

Limitations

• The dimmer, battery and support must be carried as part of the kit.
• The RGB power rating is lower than the white rating.
• The Gaffer Kit and standard kit have different modifier contents.

Practical uses

Portable key. Place the long face horizontally for an interview or vertically for a narrow product reflection. Meter with the chosen diffuser installed.

Concealed accent. Place the head in a set recess using appropriate support and run the cable to an accessible controller. Keep the emitting face and controller ventilated.

Colour detail. Use RGB for a background accent or motivated practical colour. Match the colour on camera, because equal numerical settings on different fixtures need not produce equal results.

Back to contents

Output and colour

The table below reproduces Aladdin’s model-specific illuminance figures in lux. The product page does not state the modifier configuration alongside the table; use these figures as that published reference, rather than assigning them to a particular softbox.

A grid helps limit spill but does not focus the mat into a hard beam. The working result depends on source distance, the diffuser and its separation from the LEDs.

Setting	0.6 m	1 m	2 m	3 m
5600 K	3700	1440	375	190
3200 K	3900	1500	380	190

Back to contents

Power and batteries

Use the matching AC supply or the approved V-mount battery arrangement through the MM-DIM-LM. Check the power unit and battery labels rather than borrowing the 48 V requirement from the larger MOSAIC panels.

The 1×1 page lists ALL-1-ACAD, while the 1×2 lists ALL-2-ACAD. Check that a used kit contains the correct adapter for its panel. Battery energy and continuous discharge capability are separate checks.

Battery planning and controller compatibility

Item	Package check
Panel / supply	MOSAIC MINI 1×2; the accessory chart identifies ALL-2-ACAD as its AC adapter.
MM-DIM-LM	The December 2024 manual lists MOSAIC MINI, BI-FLEX M3 and BI-FLEX M7 compatibility. Match the panel cable as well as the controller.
Battery operation	V-mount at the dimmer; use the approved battery voltage and continuous-output rating for the supplied package.
Runtime example	98 Wh ÷ 100 W ≈ 0.98 hours using the white-light head rating alone. This is an energy calculation before controller losses and battery cut-off, not a measured runtime.

The RGB and variable-white wattage figures describe different emitter operation. Check the actual crossfade/colour mode and battery load rather than adding those ratings into an assumed wall-socket draw. A spare battery and an accessible dimmer often matter more to a location setup than the bare panel’s small transport size.

Control, cooling and camera operation

The MM-DIM-LM provides LumenRadio and Bluetooth. Wired DMX uses the model’s DMX-Y cable to the controller’s jack connection; include it when a five-pin console connection is required.

The December 2024 controller manual lists 348 g and 140 × 100 × 50 mm, differing from the product-page dimensions and 373 g mass. Confirm the actual controller revision when planning a compact case or mount.

The product page rates the fixture IP20. Keep the dimmer, battery and connectors dry, leave airflow around the head and test the intended shutter, frame rate and low-level fades.

MM-DIM-LM setup

• Switch the dimmer off before changing the panel. Connect the correct sheet and power source, then switch on and check the detected panel type on the display.
• Use the intensity dial and CCT dial for local control. The green/magenta functions apply to RGBWW panels, not to an attached bi-colour-only M3 or M7.
• For wired DMX, include the MM-YDMX mini-jack adapter cable. In the DMX menu, choose Wired or LumenRadio, confirm the selection and allow the controller to reboot.
• Choose Simple or Expert mode, then match the console footprint and start address. Clear the stored LumenRadio link when transferring the receiver between transmitters.

DMX personalities and patching

Aladdin’s December 2025 DMX map lists the following colour personalities for MOSAIC MINI colour panels. Select the matching personality on the actual controller and in the console; the fixture name alone does not identify its channel footprint.

Personality	Footprint	Channel functions
Simple CCT / crossfade / RGBW	8 channels	1 intensity; 2 CCT; 3 green/magenta; 4 white/colour crossfade; 5 red; 6 green; 7 blue; 8 white.
Expert CCT / crossfade / RGBW + effects	11 channels	Channels 1–8 as above; 9 effect selection; 10 effect intensity; 11 effect speed.

For these footprints, a start address of 505 is the last complete eight-channel patch in one 512-channel universe; the eleven-channel profile must start at 502 or below. Channel 3 values 120–145 are the map’s neutral green/magenta band. Keep the crossfade and effects channels in the intended state when testing a white cue.

The product page specifies 2300–12,000 K, while the general DMX map labels its CCT channel 2200–12,000 K. A console map endpoint is not a separate measurement of the panel’s white range. Check the selected head and meter the working light when matching at the warm end.

The controller manual lists passive cooling, −10 to 40°C operation and a dry-use warning. Its technical table says 1–100% dimming although the operating pages describe a 0–100% dial range. Verify the lowest usable fade and the blackout command on the supplied revision.

Back to contents

Modifiers, rigging and the working package

The MM-2-KITCVM includes panel, dimmer, supply, 3 m cable, ball head, frame, diffuser and soft case. The MM-2-KITG Gaffer Kit adds a softbox and softbox grid.

The 1×2 X-Bend, frame, softbox and round diffuser are distinct mounting and shaping options. Check the matching attachment and ball-head interface before assembling a kit. Keep the cable from pulling on the fabric head.

Shape and support options

Accessory path	What changes
1X2-XB X-Bend	A compact rear support for a light travel package; use the ball-head interface intended for that holder.
1X2-FR-KIT frame	A supported flat face with its own fitted diffuser and frame grid.
1X2-SBX softbox	A different diffusion depth and fitted grid; frame grids and softbox grids are separate parts.
1X2-BALL / ball diffuser	A rounder emitting shape for a different reflection and spill pattern; keep its diffuser and transport bag together.

The frame ball head and X-Bend ball head are listed separately. Check the mounting interface when buying used parts; a controller that accepts the panel does not establish mechanical compatibility with another size’s frame or softbox.

Back to contents

Alternatives and related fixtures

Fixture	Choose it for
Aladdin BI-FLEX M7	A square variable-white alternative.
amaran F21c	A larger rectangular colour mat with a different power and control package.
MOSAIC MINI 1×1	300 × 300 mm RGBWW mat, 50 W white / 20 W RGB. The MM-DIM-LM and compact support options suit a portable square source.
BI-FABRIC 2	300 × 600 mm, 100 W bi-colour fabric head. A rectangular white source with its own controller and revision-specific power details.
MOSAIC 2×4	550 × 1100 mm RGBWW mat rated 350 W white / 250 W RGB; a smaller large-format source than the 600 W MOSAIC heads, with its own frame and 48 V supply.

Back to contents

Videos

Aladdin MOSAIC MINI overview

Manufacturer introduction to the MINI panels and their operating package.

Back to contents

Rental and used-fixture checks

Check every white and RGB region for uniform operation. Inspect the short lead, fabric attachment points, frame, ball head and locking connections.

Test AC power, the intended V-mount battery, app pairing and radio reception. Confirm the DMX-Y lead, diffuser, grid and case contents against the specific kit.

Documentation and specifications

• Official model specifications
• MM-DIM-LM controller manual
• MINI 1×2 accessory chart

Browse Aladdin lights, LED mats or the equipment directory.

Back to contents