Last Updated 7 hours ago
Select LED 30 Overview



The Select 30 has a longer, narrower emitting area than the Select 20. That shape gives useful coverage across a bench seat or a long reflection in a car door.
- Type
Legacy colour-capable LED soft panel with a separate controller. - Power
150 W LED-150X controller, 100–240 V AC or 18–36 V DC. - Colour Temperature2700–6500 KWhite menu; firmware colour menus extend from 2500 to 9900 K.
- Weight / Mount
12 lb / 5 kg as printed fixture per Kino Flo; separate 2 kg controller. Verify the rigging package before mounting. - Beam Control
Broad soft output; use barndoors or a louvre to limit spill. - IP Rating
No numerical IP rating stated in the archived specifications; do not assume water protection.
Select LED 30 Specifications
| Specification | Details |
|---|---|
| Manufacturer and Model | Kino Flo Select LED 30 |
| Controller | LED-150X, 150 W |
| Fixture Dimensions | 40.5 × 10.5 × 3.5 in.; 103 × 27 × 9 cm; 6.5 in. / 16.5 cm barn doors |
| Fixture Weight | 12 lb / 5 kg as printed; these are not exact equivalents |
| Controller Dimensions and Weight | 15 × 4.5 × 3 in. / 38 × 11.5 × 8 cm; 4.5 lb / 2 kg |
| Input | 100–240 V AC, 50/60 Hz; or 18–36 V DC |
| DC Current | 6.25 A at 24 V DC in the archived technical specifications |
| White Menu | 2,700–6,500 K, dimming and green/magenta |
| Colour Menus | 2,500–9,900 K, gel presets, hue/saturation and RGB with the corresponding colour firmware |
| Dimming | 100–1% in the archived specifications |
| Archive Status | Discontinued March 2018 |
Output Calculator
Select the published setup and a manufacturer distance, or enter a custom throw where supported. The results describe centre-beam output, not the brightness across the whole beam.
Camera Settings
If the calculator does not load, use the published photometric table or source on this page. JavaScript is required.
F-stop is a planning estimate, not a meter reading. It uses direct, on-axis illuminance and includes only the optics and diffusion named in the selected setup. Meter on set to account for lens transmission, filters, added diffusion, bounce, dimming and ambient light.
How the exposure estimate works
N = √(E × ISO × t / C), where E is illuminance in lux and t = shutter angle ÷ (360 × fps). The default C = 340 is a dome reference; C = 250 is a flat reference. These are calibration constants, not a measured T-stop. A small nonzero digit is tenths of a stop above the displayed full stop.
Distance estimates and comparisons
Published points are used as given. Between published points the calculator fits a curve through the two nearest readings. Outside those points it uses the inverse-square law only when the fixture’s dataset permits it. Distances outside a configuration’s supported range are reported separately. Comparisons use one shared distance and camera setup; equal lux does not imply equal coverage.
View published readings for the selected configuration
The factory chart does not identify the colour temperature or dimmer setting used for these measurements.
Strengths and Limitations
- The long narrow face makes a continuous highlight easier to place.
- A long rectangle is awkward to hide in a tight corner or low vehicle interior.
Practical Uses
Place the long axis along the subjects for a two-shot. Turn it upright when you want a narrow reflection down a bottle or a more continuous edge on a standing subject.
Output and Colour
| Metres | Factory Lux | Converted fc |
|---|---|---|
| 0.5 | 7,270 | 675.4 |
| 1 | 2,470 | 229.5 |
| 1.5 | 1,190 | 110.6 |
| 2 | 683 | 63.5 |
| 2.5 | 445 | 41.3 |
| 3 | 312 | 29.0 |
| 3.5 | 233 | 21.6 |
| 4 | 181 | 16.8 |
| 4.5 | 146 | 13.6 |
| 5 | 117 | 10.9 |
Kino Flo’s original Select 30/20 photometric chart supplies ten metric-distance readings for this model. The calculator uses only that metric series and remains bounded to 0.5–5 m. Foot-candles in this table are conversions from lux, not the separate factory feet-distance readings below. Intermediate calculator values are estimates. The chart does not specify CCT, dimmer setting, louvre or diffusion configuration, or AC versus DC test power; these values should not be presented as a verified result for a particular setting or accessory.
| Factory Distance (ft) | Factory Foot-Candles |
|---|---|
| 2 | 510 |
| 4 | 161 |
| 6 | 75 |
| 8 | 43 |
| 10 | 28 |
| 12 | 20 |
| 14 | 15 |
| 16 | 11 |
| 18 | 9 |
| 20 | 8 |
Power and Batteries
The LED-150X controller is rated at 150 W. It accepts mains or 18 to 36 V DC. Record the firmware and console profile before combining different generations.
The manufacturer’s colour-update overview identifies wired DMX and LumenRadio wireless DMX, and explains that the original white-light controller gained colour menus through a firmware update. Its input example is 1.25 A at 120 V AC. The archived specification sheet lists the controller separately from the lamphead, so add controller weight when planning the complete rig.
Control, Cooling and Camera Operation
For a repeatable cue, label the controller with its firmware, DMX personality and address. Establish the scene white balance and match the paired fixture before moving into gel or hue controls; check a low-level fade at the intended shutter.
Modifiers, Rigging and the Working Package
The 40.5-inch head is relatively narrow. The louvre contains lateral spill while the doors can keep the ceiling or floor darker.
Fixture Size and Working Package
The Select 30 and 20 use the same LED-150X family, but the 30 is the long head. Confirm the exact head, louvre, the straight or curved mount supplied with the package, and the extension cable using the Select controller manual. Do not treat a later FreeStyle kit as a drop-in parts substitute.
Alternatives and Related Fixtures
Need the shorter head? See the Kino Flo Select LED 20 specifications and Output Calculator for the other fixture’s own factory readings.
For the later long-format colour fixture, see Kino Flo FreeStyle 31.
The archived Select head is CFX-SL30 with the Select LED-150X controller. The FreeStyle operating manual identifies the later CFX-F31 and FreeStyle LED-152X controller separately. Check the head label, panel, cables and firmware on the kit rather than assuming parts or output transfer between the two.
What People Are Saying
American Cinematographer, Outlander
Cinematographer Alasdair Walker told American Cinematographer that he used Select 20 and Select 30 fixtures for soundstage interiors at night on Outlander. He found the light stayed true when dimmed and described curved Depron and diffusion frames for softer skin tones. This is firsthand evidence for both fixtures in that setup, not a comparison between the two head sizes.
Independent Measurements
In Indie Cinema Academy’s independent studio tests, the exact Select 30 measured TLCI 98.4 at a measured 2,920 K and 98.9 at a measured 5,488 K. Those are colour-rendering observations for the tested unit, not target set points or output settings for Kino Flo’s separate lux chart.
Field Feedback at a Glance
What worked
- Stays consistent when dimmed. Alasdair Walker used both Select 20 and 30 heads on Outlander and found they held their colour through dimming in his setup. Read Walker’s lighting breakdown.
- Move the controls off the head. The removable Select 150 LED DMX controller and 25 ft X12-25 extension let the head sit high or in a tight space without putting all the electronics there. Kino Flo’s kit and mounting diagram.
- Strong measured colour rendering. Indie Cinema Academy measured TLCI 98.4 at 2,920 K and 98.9 at 5,488 K on its Select 30, not on the smaller head. Read the Select 30 results.
Drawbacks to plan for
- The extension and controller are part of the working package. An inexpensive used head by itself is not a usable kit. Check for the Select 150, matching head cable, mount, and the AC cord or approved 24 V supply you need. Kino Flo’s original package list.
- Verify the modes on the actual controller. Kino Flo documents 2,700–6,500 K in White mode and a wider 2,500–9,900 K range in Colour mode. Don’t assume the wider range or available options from a used listing; verify the firmware and menu during prep. Read the White and Colour mode comparison.
- Allow for extra diffusion when the scene needs it. Walker did not rely on the bare unit for every soft skin tone. He added curved Depron and diffusion frames on Outlander. Confirm the fixture can deliver the level you want through the actual modifier. See the on-set diffusion setup.
Videos
At the Bench with Jem Schofield: Kino Flo Select 30 LED System
Rental and Used-Fixture Checks
Check doors, louvre and mount, then test the controller with its full-length head cable. Firmware affects the available white and colour controls.
Before You Book
- Confirm the long head, louvre, LED-150X controller, head cable and correctly rated mount before booking.
- Allow enough clearance for the 40.5-inch head and its doors before choosing the rig position.
- Test the actual controller firmware and console mapping through the supplied cable, then check dimming and white match on camera.
Documentation and Specifications
- Kino Flo Select 20 and 30 technical specifications
- Kino Flo Select system introduction and colour-menu overview
- Kino Flo original Select 30/20 photometric chart
Back to contents · Browse Kino Flo lights · Browse all lighting equipment