LTM Cinepar 1200W HMI PAR

Last Updated 20 minutes ago

LTM Cinepar 1200W Overview

LTM Cinepar 1200W HMI PAR lamphead
LTM Cinepar 1200 head, lenses and electronic ballast in the DeHaven Camera kit.
Kit with electronic ballastDeHaven Camera’s Cinepar 1.2 kW kit with a Lightmaker electronic ballast; check which ballast is supplied.
LTM Cinepar 1200 purchase photographed with the head, barn doors, cable and accessory lenses.
Rental kit and lensesA Cinepar 1200 kit with the lenses and cables laid out. Photo: Northwest Grip & Lighting.

The LTM Cinepar 1200 is a 1,200 W single-ended HMI PAR identified as model HH286K and item LTC1200. The lamp sits on the reflector axis.

LTM’s 286K factory page documents three 205 mm spread lenses plus a 200 mm Fresnel. The B&H catalogue lists six lenses; do not assume that older package describes the same optical set.

Detail photo

  • Single-Ended HMI PAR Single-ended MSR lamp · Cinepar 286K; G38 base. See the HMI ballast and head-cable guide.
  • 1,200 W + External Ballast Nominal lamp rating; separate magnetic or electronic PFC ballast. Read the ballast nameplate for mains draw.
  • Colour TemperatureDaylight from the installed 1,200 W lamp, not a fixture setting.
  • Weight Not stated in the cited 286K specifications.
  • Beam Angle Lens-dependent; archives disagree on which large lens produces which beam shape
  • IP RatingNot specified in the cited documentation. Read the IP rating guide.

LTM Cinepar 1200W Specifications

Manufacturer reference286K
Lamp1,200 W single-ended MSR; G38; LTM 809025
OpticsThree 205 mm spread lenses with rings, plus a 200 mm Fresnel
Door accessory diameter229 mm
Control gear1,200 W magnetic or 575/1200 W electronic PFC
Head cableA662, 10 m
LTM manufacturer specifications, archived 2008 edition. Match the exact head revision and fitted components.

Strengths and Limitations

Strength: The 286K can change coverage using its spread lenses or Fresnel without changing lampheads. Limitation: LTM’s original optical set and a later catalogue list different lenses. Check the markings and meter the head with the actual optic instead of choosing from a mixed chart.

Practical Uses

UseWorking approach
Long-throw daylight PARChoose the appropriate optic when centre intensity and reach matter.
Window and exterior workChoose the lens from both field size and intensity, then verify spill control.
Legacy rental packageVerify the 1,200 W head against the actual ballast and cable connector set.
Applications are planning guidance, not manufacturer performance claims.

Output and Test Conditions

The B&H table has contradictory foot/metre distance labels. LTM’s English and French manufacturer tables also differ in output and in the beam shapes assigned to Large and Extra-large. Those mode labels cannot safely be merged or relabelled to create an exposure calculator.

Power, Ballast and Lamp Circuit

LTM lists 1200 W magnetic or 575/1200 W electronic PFC control gear and the A662 10 m cable. Confirm supply range, frequency, input current and connector compatibility from the individual ballast nameplate.

Lamp voltage is the controlled output of the matched ballast. It is not the mains supply voltage. Size distribution from the ballast nameplate at the local supply voltage and frequency.

Control and Warm-Up

Confirm the ballast model and whether it offers adjustment before relying on a cue. LTM lists both magnetic and electronic ballast options for this head, so do not assume identical controls across rental packages. For high-speed work, test the matched head and ballast at the actual camera frame rate and shutter.

Rigging, Accessories and Safety

Use the yoke on a rated Junior support if the physical spigot confirms that fit. The surviving catalogue excerpt does not state the spigot size, so inspect it rather than inferring from head wattage.

LTM documents UV-protective glass and a safety interlock. Inspect the UV protection, interlock, lens retention, yoke, lamp holder, head cable and accessory retention before energising the head. Use a rated support and an independent safety cable.

The LTM factory accessory list identifies the following parts. References apply to the documented head and optical set; verify the actual generation, fittings and supplied rings before ordering.

AccessoryLTM Reference
Four-Leaf Barndoor / Gel FrameA 174 / A 559
Lens CaseA 676
Spread-Lens Ring286K228
Medium / Large / Extra-Large Lens8000133 / 8000134 / 8000135
Frosted Fresnel / Its RingA 760 / A 760 02
Black Ranker Stand300005B

Alternatives and Related Fixtures

For a 1.2 kW daylight Fresnel that changes beam spread without lens swaps, compare the ARRI Compact 1200.

Choose the ARRI M8 when you need to adjust the beam without swapping spread lenses. The original Joker-Bug 800 is a smaller lens-based alternative when the working setup does not need a 1,200 W head. Each requires its own matched ballast and cable.

What People Are Saying

Field feedback at a glance

What worked

  • Spot a small area without washing the surroundings. Shane Hurlbut’s narrow-lens test produced a tight patch on a white surface. Filmmakers Academy
  • Fill more of a bounce evenly. Hurlbut’s super-wide lens spread the beam across more of the white surface than the bare head did in his demonstration. Filmmakers Academy
  • Change the orientation of the spread. Hurlbut showed the same wide lens throwing a horizontal or vertical pattern when rotated, useful for shaping the beam to a bounce or background. Filmmakers Academy

Drawbacks to plan for

  • Lens changes interrupt adjustments. Hurlbut found that the lenses got hot and noted that adjusting the spread meant handling and changing the lenses rather than turning a knob. Filmmakers Academy
  • The newer 800 W comparison light metered brighter. Hurlbut’s Cinepar read f/22 while his ARRI M8 read half a stop higher in that side-by-side setup. Filmmakers Academy
  • The tested lamp was cooler than expected. Hurlbut measured 7,550 K from the Cinepar and 6,000 K from the ARRI M8 in that comparison. He noted that lamp age might explain some of the difference; meter the actual lamp before you plan to match the two heads. Filmmakers Academy

Videos

Shane Hurlbut demonstrates the 1.2 kW Cinepar’s interchangeable lenses and compares one narrow-beam setup with an ARRI M8. The comparison is specific to the filmed setup, not a universal output claim.

Rental and Used-Fixture Checks

Before You Book

Confirm HH286K or LTC1200, single-ended 1,200 W lamp, the exact lens set and rings, UV protection, ballast, head cable and accessory retention. Test strike, warm-up, hot restrike and flicker behaviour.

Documentation and Specifications

LTM original manufacturer model page · French manufacturer edition

B&H SourceBook archival LTM catalogue.

Browse LTM · HMI lights · HMI ballast and head-cable compatibility · all equipment.