Nanlux Evoke 1200

Last Updated 5 hours ago

Overview

Evoke 1200 daylight head with reflector on set

The original daylight Evoke 1200 is a large COB head with interchangeable NL-mount optics. It works as a hard window source or a distant bounce. Nanlux also documented a separate fixed-tungsten version of this model.

  • Type
    Fixed-daylight COB LED spotlight with interchangeable NL optics.
  • Power
    1,200 W rated head; separate 100–240 V AC power supply.
  • Colour Temperature5600 KThis daylight version is fixed; the 3200 K model is a separate fixture.
  • Weight / Mount
    6.94 kg head, 1.84 kg yoke and 10.5 kg power supply. NL optic mount.
  • Beam Control
    Interchangeable 26°, 45° and 60° reflectors, compatible Fresnel and soft modifiers.
  • IP RatingIP54 Dust-protected and splash-resistant in the specified configuration. See the IP Rating Guide.

Jump to Output Calculator ↓

Key specifications

SpecificationDetails
Manufacturer and modelNanlux Evoke 1200
Source or rated power1,200 W rated head
Optics, colour or format5,600 K daylight version
Head or system detailNL mount, separate supply

Photometric Output Calculator

Estimate centre-beam illumination and the corresponding camera aperture from this fixture’s published measurements.

Estimated output

Illuminance—lux
Foot-candles—fc
Estimated f-stop—Full stop + tenths of a stop

Select a configuration to calculate.

Manufacturer readings are for the stated optic, colour setting and full output, measured at the beam centre. Values between measured distances are interpolated. Point-source values outside those distances are approximate inverse-square estimates; large sources cannot be reliably extrapolated and are limited to their measured range. Exposure uses frame rate, shutter angle, ISO and the selected incident-meter calibration. Only the optics and diffusion explicitly listed in the measurement are included; additional modifiers, bounce, beam edges, ambient light, ND filters and camera exposure-index differences are not accounted for. Confirm critical exposures on set with a meter.

Model and Family Fit

This is the fixed-daylight Evoke 1200. Compare the 1200B separately when variable white is required; neither the output charts nor optic results are interchangeable.

Strengths and limitations

  • The optical family gives several measured beam widths for a single high-output daylight head.
  • This head is fixed at 5,600 K. To match a 3,200 K tungsten setup, use CTO gel in a suitable holder to warm the beam. Check the result on camera and re-meter for the light the gel absorbs.

Working with the Evoke 1200

Compare the bare head with the 26° and 45° reflectors at the actual throw. A higher centre reading from a tighter reflector can leave the corners of a large frame underfilled.

Output and photometrics

ConfigurationDistanceLuxFoot-candles (converted)
5,600 K · bare3 m5,532514
5,600 K · bare5 m2,373220
5,600 K · bare7 m1,266117.6
5,600 K · bare10 m67963.1
5,600 K · 26° reflector3 m58,0505,393
5,600 K · 26° reflector5 m18,3701,707
5,600 K · 26° reflector7 m9,180853
5,600 K · 26° reflector10 m4,626430
5,600 K · 45° reflector3 m18,4601,715
5,600 K · 45° reflector5 m6,583612
5,600 K · 45° reflector7 m3,671341
5,600 K · 45° reflector10 m2,021187.8

Photometric source and test conditions.

Independent Measurements

Newsshooter’s daylight unit measured 14,100 lux at 3 m with the F-35 Fresnel at 45°. Its 11° test showed a pronounced centre hotspot and materially different readings depending on where the meter was placed; the field was flatter at 45°. Use the manufacturer chart in the calculator, and check both centre and edge in prep when that beam is doing critical work. Newsshooter’s independent measurements.

Power and controls

A separate supply feeds the head at up to 48 V DC and 25 A. The original daylight model supports DMX/RDM and wireless control.

Control and Camera Operation

Confirm the planned control mode and run the light through a cue with the selected fan mode. Make the sound and on-camera checks with the head in its working position.

Optics and mounting

The NL mount accepts reflectors and the optional Fresnel. The 26°, 45° and 60° reflectors throw different fields even at the same dimmer setting.

Choosing the Optic or Modifier

Choose the narrower or wider NL reflector by coverage at the planned distance. If considering the F-35, check the beam centre and door gaps at the actual setting rather than assuming a uniform field.

Comparable fixtures

For the bi-colour Evoke in this power class, see Nanlux Evoke 1200B. For a higher-output bi-colour alternative, compare the Evoke 2400B and account for the larger power requirement.

What People Are Saying

Field Feedback at a Glance

What worked

  • The daylight head had enough output to serve as a high-power source on mains in Allard’s test. Matthew Allard ACS, Newsshooter.
  • He found the tint relatively neutral, even though the measured color temperature didn’t always match the label. Matthew Allard ACS, Newsshooter.
  • Sheldon liked the native modifier selection: a tight reflector or the FL-35 Fresnel gave him a way to shape the beam in bright sun. Graham Sheldon, CineD.

Drawbacks to plan for

Matthew Allard ACS, Newsshooter

Allard saw spill through the Fresnel barn-door gaps. Check for stray light with the actual optic if you need a clean cut.

Field coverage and further reading

Video

Gaffer & Gear 173 – Nanlux Evoke 1200

Rental and used-fixture checks

Confirm daylight on the label, check the head cable and lens mount, and test the selected control and fan mode. The 1200B uses a different output chart.

Before You Book

Confirm the daylight model, power supply and head cable, then test the actual reflector or Fresnel with any doors in the rental package.

Documentation

Back to contents · Browse Nanlux lights · Browse all lighting equipment