BLAIR is Aputure’s five-emitter LED light engine: blue, lime, amber, indigo and red. It mixes those emitters to make adjustable white light without a dedicated white emitter. BLAIR-CG adds cyan and green for a wider range of saturated colours.
The practical choice: hire BLAIR for a white-light job with broad Kelvin and tint control. Hire BLAIR-CG when the same head also has to deliver saturated colour cues. Neither name tells you how much usable light will reach the subject through your modifier.
BLAIR vs. BLAIR-CG
BLAIR
Tunable white
Use it when the job is mainly tunable white. The STORM 1200x has a 2,500–10,000 K CCT range with green–magenta trim. It also has xy control for colours within its gamut. That mode doesn’t give it the same range of saturated colours as BLAIR-CG.
BLAIR-CG
Tunable white and saturated colour
Use it when the same fixture needs to handle both a white key and saturated colour cues. The STORM 1000c offers hue/saturation, xy and gel controls. Aputure quotes roughly 90% Rec. 2020 coverage for that model versus roughly 70% for the 1200x. Those are manufacturer gamut figures, not output measurements. Compare the modes, control profiles and actual output on the exact fixtures you’re booking.
The STORM 80c is a compact BLAIR-CG option for colour accents and close work, not an output substitute for a 1000c. For a panel, Aputure lists the NOVA II family as BLAIR-CG with extended red. Don’t assume a panel and a point source share an identical spectrum, beam or output just because their engines are related.
The STORM 1200x menu also lists Limited HSIC+ alongside xy. “Limited” matters: being able to enter an xy coordinate or turn a saturation control does not mean the fixture can reach every requested colour. Check firmware and the console personality before committing an existing cue sheet to another fixture. Aputure: STORM 1200x menus.
What the indigo emitter changes
Some laundry brighteners, fabrics and coatings fluoresce under short-wavelength light. They absorb it and re-emit visible light, so a white shirt can look different under two fixtures set to the same Kelvin value. In his STORM 1200x test, Matthew Allard measured additional short-wavelength energy near 400–420 nm in the 5,600 K setting and saw a brighter background surface in his comparison. That’s a reason to test the material on camera, not a guarantee that everything will match daylight.
CIE Daylight vs. Blackbody
Think of this menu as choosing the fixture’s starting point before you trim green or magenta. Blackbody follows the Planckian locus, the colour path associated with a heated radiator. Aputure’s CIE Daylight setting is designed to target a slightly greener daylight chromaticity at higher CCTs. For the STORM and NOVA II behaviour Aputure documents, the target curves coincide at and below 4,000 K, transition from 4,000 to 5,000 K, and differ by about +0.0032 Duv at 5,000 K and above. Duv is an offset from the blackbody curve; it is not a measure of spectral fidelity. Neither menu option reproduces every window, sky condition or practical bulb. Aputure’s white-light-standard explanation.
Aputure describes several models’ tint controls as using the full ASC MITC range. That gives the control a common reference for plus/minus-green correction; it does not establish that the same console value will make two different fixtures render a red dress or a white shirt identically. ASC MITC progress report.
What independent measurements show
STORM 700x
In Matthew Allard’s test at a 5,600 K setting, Max Output and the 35° Hyper Reflector, R9 went from 76.3 in CIE Daylight to 92.5 in Blackbody.
Average CRI was 97.6 and 97.1 respectively. R9 covers a saturated red test sample and is not part of average CRI (R1–R8). That explains why the average can look almost unchanged. It doesn’t mean Blackbody is always a better match. Newsshooter’s STORM 700x measurements.
STORM 1000c
At a 5,600 K setting, 3 m from the meter, in Max Output with the 45° reflector, Allard measured 16,200 lux in Blackbody, about 11% more than in CIE Daylight in that same setup.
Recheck exposure after changing the white standard; do not assume this difference applies at other CCTs, to other optics, or to every BLAIR-CG head. Newsshooter’s STORM 1000c measurements.
STORM 1200x
In Allard’s nominal 5,600 K comparison, the Maxima 3 scored 78 SSI against the 1200x.
This is a fixture-to-fixture comparison, not either light’s score against daylight. A shared Kelvin setting and good scores against a standard don’t establish that two fixtures match each other. Newsshooter’s STORM 1200x comparison.
Matching lights on set
- Start with a camera reference. Set the lights to the same CCT, keep camera white balance fixed, and compare a neutral card, skin and a sample of the wardrobe. Trim green–magenta as needed. If you’re matching a window, try CIE Daylight where available; if you’re matching a lamp or another LED, compare that result with Blackbody. A shared number on the display is only a starting point.
- Compare the same spectral reference. An SSI score describes how closely the measured spectrum matches a named reference. Compare daylight with the same daylight reference and tungsten with the same tungsten reference. It isn’t a substitute for the camera test.
- Check the actual cue. For a saturated wash, check the output at the colour, distance and modifier you’ll use. For a dim cue, test the fade and look for flicker at the intended frame rate and shutter. Save the white standard and tint setting along with the Kelvin value so a replacement head can be set up consistently.
- Log the setup and repeat the swap. At the subject, meter at the same position with each lamp alone. Keep the camera white balance, exposure and viewing transform fixed for each comparison. Use the actual reflector, diffusion or bounce. After the first pass, equalize exposure to compare colour without a brightness difference. Record fixture and firmware, CCT, tint, white standard, modifier, distance, and output mode. If you are sweeping Kelvin during a take, test the full move: on the 1200x, Constant Output is designed to hold brightness steadier across the CCT range, while Max Output prioritizes brightness. Aputure: STORM 1200x system settings.
Equipment examples
- BLAIR: STORM 400x · STORM 700x · STORM 1200x · STORM XT52 · NOVA 9° 2×1 (BLAIR with Extended Red, not BLAIR-CG; see the exact product specification).
- BLAIR-CG: STORM 80c · STORM 1000c · NOVA II 2×1 · NOVA II 1×1 · STORM CS32 (BLAIR-CG with Extended Red). The original Nova P600c is an RGBWW fixture. Check the generation as well as the family name.
Related terms
RGBWW · RGBACL · Correlated Colour Temperature · Compare LED light engines
References
Aputure: STORM 1200x and BLAIR FAQ · Aputure: STORM 1000c and BLAIR-CG · Aputure: NOVA II family · Academy: Spectral Similarity Index